Canon Personal Copiers (PC) 12
Experienced technical support provide their insights in answering this question :
I am having the same problem, not only with my BJC-70, but also the equivalent problem with my BJC-80. Typically I am working at my computer, and the printer is powered up, but idle. All of a sudden for no apparent reason, it emits a series of beeps and returns the print head to the central position. The BJC-70 display Error F12. With the BJC80 you have to count the beeps. The problem seems to be caused by some sort of premature failure of the print head, due to an electronic fault. Sometimes, if the printer is powered down for a few minutes or longer, it will work normally for a short time after power is re-applied, but typically the problem recurs within 30 minutes, and this period of trouble free operation gradually reduces, until the print head will not work at all. The only solution is to replace the offending print head. You should, however, retain the failed head, in order to salvage any un-used ink remaining in the tanks. The new print head comes with full ink tanks. As soon as one of these fails, I replace it with an ink tank retrieved from the failed head. I don’t discard the failed head until both ink tanks have been retrieved.
How to Identify and Fix Common Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
The E07 error message appears when your Canon Pixma printer detects that the “FINE Cartridge is not installed in the correct position”. A `FINE` cartridge refers to a stand alone black or tri-colour cartridge (with a printhead attached) that is used exclusively in two cartridge printers.
Canon printers produce error codes for one of several reasons: The settings for your printer might not be compatible with the document you`re trying to print. The loading bay for your paper might have become lodged with paper or you`re using the wrong type of paper.
The P 0 7 error is an indication that your PIXMA MG3200 would require service. You are eligible for Canon`s Upgrade Program. This is for out of warranty units which have been diagnosed to require service, or for some reason are incompatible with a new or upgraded system.
For example, E07. 2 means Error 7 occurred and the inverter status was condition # “2” when the error occurred. An error code will appear on the display automatically when a fault causes the inverter to trip.
Phenomenon. In rare cases, error 70*1 or error 80*1 may repeatedly display on some EOS 70D digital SLR cameras due to an internal communication failure resulting from the structure of the electrical printed circuit board.
Err 70. A malfunction with the images has been detected. If the error message is still showing, then it is necessary for the camera to be inspected by a Canon Factory Service Center.
1. Paper Jams. Paper jams are a common problem for printers, resulting in time-consuming and frustrating delays. It can occur when loose sheets of paper get stuck in the rollers or feeding mechanism of the printer.
Select Start , then select Settings > Devices > Printers & scanners . Scroll down to Related Settings and select Print server properties. Select the Drivers tab, and see if your printer is listed. If it is, you`re all set.
Disconnect the printer cable from the printer, turn the printer off, and then unplug the printer from the power supply. Plug the printer back in and turn the printer back on. If the problem is not resolved, contact your Canon service representative.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Canon BJC-70 error message F 12
ANSWER : I am having the same problem, not only with my BJC-70, but also the equivalent problem with my BJC-80. Typically I am working at my computer, and the printer is powered up, but idle. All of a sudden for no apparent reason, it emits a series of beeps and returns the print head to the central position. The BJC-70 display Error F12. With the BJC80 you have to count the beeps. The problem seems to be caused by some sort of premature failure of the print head, due to an electronic fault. Sometimes, if the printer is powered down for a few minutes or longer, it will work normally for a short time after power is re-applied, but typically the problem recurs within 30 minutes, and this period of trouble free operation gradually reduces, until the print head will not work at all. The only solution is to replace the offending print head. You should, however, retain the failed head, in order to salvage any un-used ink remaining in the tanks. The new print head comes with full ink tanks. As soon as one of these fails, I replace it with an ink tank retrieved from the failed head. I don’t discard the failed head until both ink tanks have been retrieved.
Read Full Q/A … :
Canon Personal Copiers (PC) 12
Canon iP90 Service Error Message 5C00
ANSWER : Have same problem what the fix
Read Full Q/A … :
Canon Personal Copiers (PC) 12
canon MP 700 error message
ANSWER : It would be ideal if you take after the progressions beneath:
Read Full Q/A … :
Canon Personal Copiers (PC) 12
error message
ANSWER : Search it on google
Read Full Q/A … :
Canon Personal Copiers (PC) 12
CANON P200- ERROR 5100 PLEASE HELP!
ANSWER : Read this for solutions http://www.mytechtime.com/2011/10/canon-error-5100-how-to-fix.html
Read Full Q/A … :
Canon Personal Copiers (PC) 12
Canon MP530 – Head Alignment Error
ANSWER : Hi Trigger, can you please let me know how this was resolved as I have a similar problem.
Read Full Q/A … :
Canon Personal Copiers (PC) 12
Canon Pixma MP150 Error Code 5100
ANSWER : Make sure you check that a copy of Gustave Holst’s journey to the stars cassette isn’t stuck in there! haha. That’s what my error 5100 was all about, I was getting ready to dismantle the thing after threatening it with a water boarding.
Read Full Q/A … :
Canon Personal Copiers (PC) 12
Canon Pixma iP3000 "Open door" Error code.
ANSWER : Look for a protruding plastic on the top that goes into an indentation. Mine was in the front left side. Put a piece of cardboard into the indentation.and close the door. The top plastic piece is not pushing the door close sensor down and because its too short and the cardboard allows the sensor to be reached and pushed.
Read Full Q/A … :
Canon Personal Copiers (PC) 12