Xerox Color Qube 8570 Error Code

Unknown Printer
I have error problem 93,599 thank you

How to Identify and Fix Common printer Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

91,721 means Printhead Tilt Fault. I suggest you look for ink spills or obstructions around the printhead, and try to remove as much as possibe, also reboot the printer.

Fault Code 94,700 – Process Drive Error – Broken Transfix Camshaft. Unless you are very comfortable taking it apart and have a Service manual to get deep enough to locate the broken part, and have access to order the part when you find it it may be done for.

Re: ColorQube 8580 printer error 91, 720.00:25182

This obviously means there is a Printhead Tilt Fault.

This error displays because a fault was detected during a DHCP operation. Input a new static IP address or correct the BOOTP server address. If necessary, contact your System Administrator for addtional support.

This fault indicates that the paper did not turned on the feed out sensor at the correct time. Perform the following: Check for paper handling failure due to obstacles on the paper path.

Error 018-755 – there is no response from the server and failed to establish TCP/IP session. Check the destination Computer/Server. Check the router that the Computer/Server and the multifunction device are connected to make sure there is communication.

Fault Code 017-714 occurs when the device is unable to Communicate with the SMTP server using SSL, TLS or STARTTLS Encryption. NOTE: The Scan to Email Feature is only available on the Copier/Printer model.

Fault Code 099-395: Fuser Motor Current Failure.

To change your printer IP address, type its current IP address into the address bar of a web browser. Then go to the Settings or Network page and change your printer`s network to a static/manual IP address. Finally, type in the new IP address.

Verify the user has write access to the storage destination on the SMB server. For details, refer to Configure Network Authentication for Security. Verify a firewall is not blocking communication ports.

There is an IP address conflict with another system on the network (WiFi). Have your Network Administrator change the IP Address of the systems the machine is connected to. If the problem persists, contact Support for additional assistance.

Fault Code 071-104: Tray 1 Pre Registration Sensor On Jam.

Check that paper in Tray 1 is loaded correctly. Check for jammed paper in Tray 1. If the problem persists, contact Support for additional assistance.

Typically, Fault Code 018-772: “Shared Name Not Found in Server” is indicating that the VersaLink cannot find the SMB Share that it is trying to send the scan to.

Fault Code 018-505 appears when an Authenication Failure has occured when attempting to log into the SMB Server. Make Sure the SMB Settings such as Host Name or IP, Share Name and Document Path are Entered Correctly. Make Sure the Credentials Used to Login to the SMB Server are Entered Correctly.

Fault Code 075-109: Paper From Tray 5 On Pre Registration Sensor.

This fault indicates that the black corotron cleaner is unable to clean the corotron. NOTE: Do not actually replace the Charge Corotron with a new assembly. Use the procedure as a guide to swap corotrons between 2 different color stations.

Fault Code 027-779 occurs when the connection to the SMTP Server fails due to Authentication Failure, possibly due to an incorrect login name and/or password. NOTE: The Scan to Email Feature is only available on the Copier/Printer model.

This fault indicates that the paper did not turned on the feed out sensor at the correct time. Perform the following: Check for paper handling failure due to obstacles on the paper path. Check that the proper paper type is installed in the tray.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Xerox Color Qube 8570 Error Code

ANSWER : From Service Manual

Read Full Q/A … :
Unknown Printer

error code :91,720,00:60960

ANSWER : Xerox 8570 Error Code 91720

Read Full Q/A … :
Unknown Printer

HP Color Laserjet 500 series M551n Error 98.00.0C

ANSWER : I just ran into one of these on a 4 year old m551. Failed to complete startup at the end of disk check. Followed the above link for troubleshooting.

Read Full Q/A … :
Unknown Printer

Canon Pixma MP150 Error Code 5100

ANSWER : Make sure you check that a copy of Gustave Holst’s journey to the stars cassette isn’t stuck in there! haha. That’s what my error 5100 was all about, I was getting ready to dismantle the thing after threatening it with a water boarding.

Read Full Q/A … :
Unknown Printer

Error Code 52.1M

ANSWER : Magenta laser error. The spinning motor bearings cause the squeal and that slows it down causing the error. You could try opening it and lubricating the motor shift with a drop of synthetic lubricant. Do not use more than a drop.

Read Full Q/A … :
Unknown Printer

First error 58.00.04, then 57.00.03

ANSWER : Did you ever get a resolution for the 57.00.03 error? I’m having a similar problem with an M602 model. Thanks.

Read Full Q/A … :
Unknown Printer

Error Code 51.1 says Printer Error No Kidding.lol

ANSWER : Sometimes turning off and on will allow you to print a few pages. The error is a beam detect error. The only real fix is to replace the laser scanner unit. Could be a loose connector on the scanner or DC controller from the scanner. That’s unlikely. You could try the only other free fix which is to open the scanner assy. and clean all the mirrors inside. The dust could obstruct the laser beam enough to cause the detect error.

Read Full Q/A … :
Unknown Printer

Xerox 7760 Wrong paper size error when trying to print to A4

ANSWER : At first you could try to print using the Multifunction/Bypass Tray on the left side of your printer.

Read Full Q/A … :
Unknown Printer