Canon Pixma MP150
Experienced technical support provide their insights in answering this question :
Cereal box trick worked on my Canon MG-2922. Found McDonald’s Monopoly pieces. No winners though. Thanks for the idea… saved some $.
How to Identify and Fix Common Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
One of the most common causes of paper jams is that the paper has simply not been loaded correctly into the printer paper feed. With this in mind, remove any paper from the tray in order to check for any jams. If you do see some paper jammed, pull each sheet out of the printer slowly until the printer is clear again.
Sometimes a paper jam error persists even though there is no jammed paper (false paper jam). Reset the printer, which might clear a false paper jam error, and then try to print again. With the printer turned on, disconnect the power cord from the printer. Unplug the power cord from the power source.
A piece of paper stuck in the paper tray or inside the printer can create a paper jam. Paper jams can occur for a variety of reasons, such as overloading the paper tray, loading different thicknesses of paper in the tray, or using paper that isn`t appropriate for your particular printer.
If your printer has a paper path cover behind the carriage, remove the cover, and then remove any jammed paper. Pull out the input tray, and then remove any jammed paper. If your printer has a bottom cleanout door, carefully lift the printer and look under it, and then remove any jammed paper from the bottom cleanout.
During a print job, the printer stops feeding pages, and a Paper Jam error message displays on the printer control panel. This indicates that paper might be jammed inside the printer. note: Paper jams can be real or false. The printer might report a paper jam even when there is no jammed paper.
A paper jam is when paper or other printed material gets stuck or lodged in a printer and cannot eject.
Slide the paper all the way into the printer. The leading edge of the paper will stop at the Paper Drive Roller. Locate the Paper Sensor/OOPs sensor on the right side of the paper path. It can be seen from the top of the printer with the Top Cover open and has red, black, and blue wires attached to it.
If your printer`s status displays “Printer in error state,” there may be a problem with the printer itself. Make sure the printer is turned on and connected to your PC by Wi-Fi or cable. Check it for low paper or ink, and be sure the cover isn`t open and the paper isn`t jammed.
Document Jam means the document in the automatic document feeder (ADF) was loaded or fed improperly or was too long. The error message may be followed by Clear the scanner jam.
Over time, paper absorbs and loses moisture which causes it to warp, or not lie perfectly flat. This can create print quality issues like jamming and is something to consider when using a printer that hasn`t been used for a while.
You have two options to factory reset Canon printers. One method is to use the Reset button, while the other is to utilize the Setup option.
Capacitive sensors can detect objects that have a dielectric constant that is different from air. Hence, these sensors can detect objects made from a wide variety of materials such as plastic, paper, wood, etc.
Canon printers produce error codes for one of several reasons: The settings for your printer might not be compatible with the document you`re trying to print. The loading bay for your paper might have become lodged with paper or you`re using the wrong type of paper.
The following are the top reasons why paper jams occur:
unsupported paper/media is used. incorrect paper settings in the tray and/or the print driver. paper loaded incorrectly and/or paper edge guides not adjusted properly in the tray. humidity and/or paper condition and storage.
The message Paper Jam may appear on the display if the Brother machine is not feeding paper correctly, paper scraps have become stuck in the print head path, the paper is not loaded properly in the paper tray, the jam clear cover located in the back of the machine, is not installed properly or the PE Actuator is …
If you encounter the E02 or E03 error, this is because the printer cable is too tight and the printer door cannot be properly closed. Look at the door on the left side of the printer, where there is a door trigger.
If you encounter the E02 or E03 error, this is because the printer cable is too tight and the printer door cannot be properly closed. Look at the door on the left side of the printer, where there is a door trigger.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.
ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.
Read Full Q/A … :
Canon Pixma MP150
paper jam error pixma mp150
ANSWER : Cereal box trick worked on my Canon MG-2922. Found McDonald’s Monopoly pieces. No winners though. Thanks for the idea… saved some $.
Read Full Q/A … :
Canon Pixma MP150
Paper Jam error but no paper jam
ANSWER : Obviously you didn’t get all the paper cleared out. There is a small scrap in the paper path causing the jam when the paper hits it. You can try clearing it out by inserting something stiff like a piece of file folder from the back of the printer into the paper path and pushing the offending piece out that way.
Read Full Q/A … :
Canon Pixma MP150
Canon Pixma Printer Paper Does Not Feed Properly/"No Paper" Error Occurs?
ANSWER : Pretty much useless advice. I also have serious doubts about someone who is obviously not fluent in the English language.
Read Full Q/A … :
Canon Pixma MP150
Canon mx410 Paper jam message, but no paper jam?!
ANSWER : I have exactly the same problem, no answers 😳
Read Full Q/A … :
Canon Pixma MP150
my pixma e400 says paper jam when it's is'nt
ANSWER : Almost everyone of these jams is because there is a small scrap of paper in the paper path that you can’t see. Try taking half of a file folder and shoving it down the paper path. That usually pops out the offending scrap.
Read Full Q/A … :
Canon Pixma MP150
Paper Jam and carriage jam code when nothing is jammed
ANSWER : Did you try cleaning the encoder strip that runs through the cartridge assy.? Use Window Cleaner on a paper towel. Also, check inside on the right. I’ve seen a lot of times where there is a folded up scrap of paper that stops the carriage from going all the way to the right.
Read Full Q/A … :
Canon Pixma MP150
Paper Output Jam error
ANSWER : Printer jams happen when the paper encouraging through the printer goes amiss. Infrequently the printer overlooks the issue, officers ahead, and expels a folded mess into the yield plate; on different events, the printer stops in mid job, and the folded mess- – or a portion of it- – stays caught some place inside the machine.
Read Full Q/A … :
Canon Pixma MP150