HP LaserJet 9040
Experienced technical support provide their insights in answering this question :
bonsoir
How to Identify and Fix Common Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
Recommended action. Turn the printer off, wait 15 seconds and turn the printer back on (using the power switch located on the back of the printer). The error code should not appear again.
This error code can appear for a few reason such as cable issues, firmware errors or hardware faults. You can try the reset processes as stated at the top of the page, then if the error code still displays update the firmware, also try using different printer cables.
The 41.2 error in the LaserJet 5Si, 8000, 8100 and 8150 is typically caused by high voltage arcing that disrupts the beam detect circuit. The most common cause of arcing is a bad connection to the transfer roller. Other possibilities are discussed at the end of the article.
If your printer`s status displays “Printer in error state,” there may be a problem with the printer itself. Make sure the printer is turned on and connected to your PC by Wi-Fi or cable. Check it for low paper or ink, and be sure the cover isn`t open and the paper isn`t jammed.
An E9 error occurs when the printer detects that ink system maintenance is required. An Ink System Maintenance page prints containing instructions to open and close the printhead access door to resolve the error.
The 24 character error code is a failure of the short Disk Self Test ( DST ) and would indicate that the Hard Drive is failing and needs to be replaced. Hi, It means the hard drive has failed the quick test and needs to be replaced.
59.10 is a main drive error, which could be a bound up fuser. 51.10 is a laser error, which could be a bad laser unit. Which error do you have? If the printer can print an engine test, then you may have a bad formatter.
1. Paper Jams. Paper jams are a common problem for printers, resulting in time-consuming and frustrating delays. It can occur when loose sheets of paper get stuck in the rollers or feeding mechanism of the printer.
The error code 0x00000040 could appear if your printer driver is out-of-date or faulty. Your printer driver may need to be updated in this situation to help with problem resolution.
The error code 0xc0000001 indicates system files are corrupted. Possibly this can be fixed by entering windows SAFE mode and running the system file checker. Post back if F8 does not work or you cannot get into safe mode.
This error might happen at any time for multiple reasons. The most common causes are due to the printer being asked to perform an action that the firmware is not capable of, and might not have been designed to perform, such as: Printing files with unsupported programming commands.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
HP 9040 MFP Error code
ANSWER : bonsoir
Read Full Q/A … :
HP LaserJet 9040
Error Code 51.1 says Printer Error No Kidding.lol
ANSWER : Sometimes turning off and on will allow you to print a few pages. The error is a beam detect error. The only real fix is to replace the laser scanner unit. Could be a loose connector on the scanner or DC controller from the scanner. That’s unlikely. You could try the only other free fix which is to open the scanner assy. and clean all the mirrors inside. The dust could obstruct the laser beam enough to cause the detect error.
Read Full Q/A … :
HP LaserJet 9040
Hp designjet 500 error code 11:11
ANSWER : I have an HP designjet 510 I just powered it on and it only shows error 11:11. does anybody have a solution?
Read Full Q/A … :
HP LaserJet 9040
HP laser jet 3015 "Upgrade Error Call HP Support"
ANSWER : rgtr
Read Full Q/A … :
HP LaserJet 9040
Error Code 52.1M
ANSWER : Magenta laser error. The spinning motor bearings cause the squeal and that slows it down causing the error. You could try opening it and lubricating the motor shift with a drop of synthetic lubricant. Do not use more than a drop.
Read Full Q/A … :
HP LaserJet 9040
HP Laserjet 4200 50.2 Fuser error
ANSWER : if you are using a good fuser the next part to try would be low voltage power supply
Read Full Q/A … :
HP LaserJet 9040
HP 4250n error 13.05.00 Phantom Jam
ANSWER : Pull and reset the fuser. Make sure both sides are back into their position.
Read Full Q/A … :
HP LaserJet 9040
HP 4050 Error 13.1 & 13.20
ANSWER : I tried the fix you recommended but it still would not fix.
Read Full Q/A … :
HP LaserJet 9040