Canon Pixma MP620
How to Identify and Fix Common Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
The 5C00 error indicates that there may be problem inside of the printer; if resetting the printer did not resolve the error, the printer will require servicing. Please call or email us at one of the methods on the Contact Us page to obtain your servicing options. Did this answer your question?
Canon printers produce error codes for one of several reasons: The settings for your printer might not be compatible with the document you`re trying to print. The loading bay for your paper might have become lodged with paper or you`re using the wrong type of paper.
If your printer`s status displays “Printer in error state,” there may be a problem with the printer itself. Make sure the printer is turned on and connected to your PC by Wi-Fi or cable. Check it for low paper or ink, and be sure the cover isn`t open and the paper isn`t jammed.
First, try rebooting your computer and turning your scanner off for a few minutes, then back on. Doing this corrects more computer and device issues than you may expect. Besides turning the scanner off, disconnect the power cord – this causes a more complete hardware reset.
This issue could be due to the printer being dirty (excess ink in the ink cartridge tray or ink overflow tray). Try cleaning the printer thoroughly and installing the cartridges again to see if this fixes the problem.
With the printer powered on, select Setup . Select Device settings . Scroll to the bottom of the menu list and select Reset settings.
The Canon 5200 error is often related to the ink levels present in printer cartridges. Turning your printer off and on again can reset the printer`s mechanism for reading ink levels and get you back to printing in no time.
This error code is 5B00. It indicates that the used ink counter must be reset and that your absorber pads must be replaced.
The Canon 5200 error is often related to the ink levels present in printer cartridges. Turning your printer off and on again can reset the printer`s mechanism for reading ink levels and get you back to printing in no time.
According to Canon, Error 06 indicates a fault of the sensor cleaning module.
The 5501 Support Code means an ink tank wasn`t recognized by the printer. You can check a few things to troubleshoot the error: Are you using the correct ink tank? Installing used ink tanks may clog the nozzles.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Canon iP90 Service Error Message 5C00
ANSWER : Have same problem what the fix
Read Full Q/A … :
Canon Pixma MP620
Canon Pixma MP150 Error Code 5100
ANSWER : Make sure you check that a copy of Gustave Holst’s journey to the stars cassette isn’t stuck in there! haha. That’s what my error 5100 was all about, I was getting ready to dismantle the thing after threatening it with a water boarding.
Read Full Q/A … :
Canon Pixma MP620
Print problem with Canon MP620
ANSWER : Open the front of the printer.
Read Full Q/A … :
Canon Pixma MP620
Canon Pixma iP3000 "Open door" Error code.
ANSWER : Look for a protruding plastic on the top that goes into an indentation. Mine was in the front left side. Put a piece of cardboard into the indentation.and close the door. The top plastic piece is not pushing the door close sensor down and because its too short and the cardboard allows the sensor to be reached and pushed.
Read Full Q/A … :
Canon Pixma MP620
canon mx 700 error code 5100
ANSWER : The problem is how the hell do you put your hand in there to clean it? I have tried but could not clean it properly, hence my printer still has that error.
Read Full Q/A … :
Canon Pixma MP620
How to fix error code B200
ANSWER : There’s lots of forum posts dealing with the B200 error. http://www.fixyourownprinter.com/posts?utf8=%E2%9C%93&q=b200
Read Full Q/A … :
Canon Pixma MP620
Error Code 51.1 says Printer Error No Kidding.lol
ANSWER : Sometimes turning off and on will allow you to print a few pages. The error is a beam detect error. The only real fix is to replace the laser scanner unit. Could be a loose connector on the scanner or DC controller from the scanner. That’s unlikely. You could try the only other free fix which is to open the scanner assy. and clean all the mirrors inside. The dust could obstruct the laser beam enough to cause the detect error.
Read Full Q/A … :
Canon Pixma MP620
error code 27
ANSWER : Waste ink pads full. They really aren’t as they hold a lot more waste ink than they can before they display that message. Read this thread for reset procedures.
Read Full Q/A … :
Canon Pixma MP620