Canon Bubblejet (BJ) 100
How to Identify and Fix Common Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
If the nozzle check pattern shows adequate ink, but the printer doesn`t print color, clean the printhead. After that, print a nozzle check pattern. After performing printhead cleaning, perform a printhead deep cleaning. If still, the problem persists, switch off your printer and do the deep cleaning after a day.
A possible cause may be that appropriate paper is not used or the amount remaining in toner cartridges is running low.
Make sure the document is set to print in color and enable the color printing feature on your printer. Check the ink level and replace the ink cartridge if necessary. Clean the print head. Most printers have an automatic cleaning feature now.
If the problem is isolated to one color, set the printer to Disable Cartridge Check and swap cartridges. If the problem disappears, the old cartridge was obviously bad. If the problem persists, something associated with the cartridge is to blame: its high voltage contact, high voltage circuit, or laser scanner.
At the Windows Manage your device screen, click Printer properties. Click Preferences. From the Color Mode dropdown, choose either Color or Black and White.
Both RGB and CMYK are modes for mixing colour in graphic design. Monitors use RGB whereas printers use CMYK. This means that RGB colour mode is best for digital designs, while CMYK is best for print materials.
Wipe clean the cartridge carriage where the cartridge connects to remove any dried ink (make sure the printer is off and unplugged). If the printhead is built into the printer, clean where the ink comes out with a damp cloth. Re-install cartridges and run a print head cleaning process.
A common cause of faded, faint printouts from your inkjet printer is dried ink particles causing a blockage in your printer. The printheads on an ink cartridge can be become blocked if the printer is not used for a period of time, so it is recommended to print a few pages each month to maintain the print quality.
Color calibration enables your printer to produce consistent colors with the particular printheads, inks and paper type that you are using, and under your particular environmental conditions.
The first step in printer calibration is to calibrate your monitor. Then, make sure you use the correct printer driver for your printer. Within the printer driver are controls for fine-tuning the overall appearance of color from your printer. Depending on your needs, this may be sufficient to get the color you want.
There may be two reasons for this: Your computer monitor has not been calibrated and profiled so it has a yellow cast and when you make corrections to you images, the results show a blue cast. You have not calibrated your printer recently and it is causing the blue shift.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Print problem with Canon MP620
ANSWER : Open the front of the printer.
Read Full Q/A … :
Canon Bubblejet (BJ) 100
Canon MP610 printhead or purge unit problem ?
ANSWER : Hello, can somebody help me here?
Read Full Q/A … :
Canon Bubblejet (BJ) 100
Canon S600 Printer Problem
ANSWER : if you have been utilizing the same cartridge for more than a couple of months, you might need to check the ink or toner levels. On most present day printers, you can check these levels utilizing programming or by a light pointer on the front of the machine (counsel the proprietor’s manual for subtle elements on marker lights).
Read Full Q/A … :
Canon Bubblejet (BJ) 100
Full Ink Tank in Canon Pixma ip4000
ANSWER : It had been exactly the same subject, could not find an appropriate broker and process for earnings finally had to rummage through the Web, and there I came across this page http://optioninvest.org .Possibly you’ll find there is a therapy to your condition, thanks for the fascination!))
Read Full Q/A … :
Canon Bubblejet (BJ) 100
Canon Pixma MP150 Error Code 5100
ANSWER : Make sure you check that a copy of Gustave Holst’s journey to the stars cassette isn’t stuck in there! haha. That’s what my error 5100 was all about, I was getting ready to dismantle the thing after threatening it with a water boarding.
Read Full Q/A … :
Canon Bubblejet (BJ) 100
Canon i560 Will not print black
ANSWER : Dang, it worked for me then wentback to normal (not working) after the test page. Oh well not bad for a 10 year old bubble jet.
Read Full Q/A … :
Canon Bubblejet (BJ) 100
Canon MP600 died
ANSWER : hey guys I found this on the net check it out maybe somebody can make something out of it cuase they omitted this part on the service manual that I attained cause I have the same problem hope this helps.
Read Full Q/A … :
Canon Bubblejet (BJ) 100
Canon Pixma iP3000 "Open door" Error code.
ANSWER : Look for a protruding plastic on the top that goes into an indentation. Mine was in the front left side. Put a piece of cardboard into the indentation.and close the door. The top plastic piece is not pushing the door close sensor down and because its too short and the cardboard allows the sensor to be reached and pushed.
Read Full Q/A … :
Canon Bubblejet (BJ) 100