Unknown Printer

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Requirements: Operating System – Windows 7, Windows 8, Windows 8.1, Windows 10.
If you are getting a 05:10 Error Code — You Must Replace Your GL/2 Accessory Card or Formatter Board. A 05:10 error on the front panel of the printer indicates a formatter card failure.
Open your image in Adobe Acrobat. Select `Print` from the tool bar or by key command. On the print dialogue window do the following: For the Printer, select “HP Designjet T120”.
This system error refers to the inability of the Carriage Encoder Sensor to properly read the encoder strip. This may happen because that sensor is damaged. However, in most of the cases, this happens because the Encoder Strip is dirty (or damaged in some specific scenarios).
If your printer is compatible with Windows 10, download and run the Print and Scan Doctor to detect and fix isses. If problems persist, reinstall the latest HP printing software. Download and Install the latest HP printer software and driver.
In Windows, search for and open Add a printer or scanner . Click Add a printer or scanner, and then wait for Windows to locate available printers. If your printer is found, click it, and then click Add device to complete the driver installation.
510-The installed number of DIMMs on one or more processors results in an unbalanced memory configuration across memory controllers. This may result in nonoptimal memory performance. Certain DIMM configurations result in unbalanced memory populations across the memory controllers within the processor.
To be specific, you should make sure that your printer has sufficient paper, ink or toner and without paper jam. If the printer cartridge`s status is faulty, you should replace it with a new one. After carrying out these operations, check if the HP printer can print properly. If not, try other methods immediately.
Insert the stack of paper into the product, and then gently push the paper guides snugly against the paper. Make sure that the paper is fully inserted into the product. Try printing again. If the issue is not resolved, try loading different brands of paper and different types of paper, one type at a time.
10 Supply memory error. The printer is unable to read the toner cartridge data. The toner cartridge is present but defective.
The 21:10 error can be caused by anything that inhibits the service station motion. The best way to troubleshoot the service station is to remove the motor and operate the white gears with your fingers to see if there is any obstruction to the movement of the sled with the 4 print head caps on it.
The good news is that pretty much any printer purchased within the last four to five years – or any printer that you`ve successfully used with Windows 7, 8 or 8.1 – should be compatible with Windows 10.
Error 11:11 is normally displayed on the front panel of your HP Designjet Printer because a fault has been detected with the trailing cable. The trailing cable is the component that provides communication between the printer electronics and the carriage PCA.
NOTE: The Designjet 510 and Designjet 800 WILL NOT be able to completely boot up without the card, it will show a message saying WARNING 05:10 (notice that this time it is a warning, not the actual System Error). Once it shows the warning please press the ENTER button. This will allow the printer to get to ready mode.
The system error 61:05 Error Processing Job error indicates there is a communication problem and the HP Designjet 800 or 500 series printer was not able to process the job that was sent to it.
Recommended action. Turn the printer off, wait 15 seconds and turn the printer back on (using the power switch located on the back of the printer). The error code should not appear again.
Turn the product on while you press and hold the Resume button for 10-20 seconds. The Attention light turns on. Release the Resume button. The Attention and Ready lights cycle while the product restores factory defaults.
If your printer`s status displays “Printer in error state,” there may be a problem with the printer itself. Make sure the printer is turned on and connected to your PC by Wi-Fi or cable. Check it for low paper or ink, and be sure the cover isn`t open and the paper isn`t jammed.
Viewing Printer Settings

From the Devices and Printers screen, right-click on a printer and choose “Printer properties” to bring up a dialog box displaying the printer name, sharing settings and port information.

Printers are configured in the Printers section of the Windows Control Panel. Printer Settings: Displays the printer settings window associated with the selected printer. The desired paper size, among other settings, can be selected in the printer settings window.
Right Click on the Lower Left Corner of the desktop, select Control Panel. Select Devices and Printers. Right Click on the printer`s icon, select Printer Properties. The Printer Properties dialogue opens.
if you get an error code on your 500 or 800 that`s an O one coulomb 10 that`s almost a for sure sign that your electronics module has draw died. there are some other error codes a 111 which means that the fan.
On the HP LaserJet M601 M602 M603 series printers, this 51.00. 10 error code may be temporary. Try turning the printer off and back on to see if the error clears. If the error comes back repeatedly, you have a failing laser scanner assembly which requires replacement.
Corrective Action: Try the following: Switch the Printer Off and wait a few minutes. Switch the Printer On again and check if the Error Code has disappeared. If the Error Code reappears, check for a new Firmware release.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Install Memory Chip Upgrade on Designjet 510
ANSWER : I am on the binary options have already been working for half a year, it all began with the seek out information for learning, which will doschit objectives and maybe not fail in the middle, and then got to me the problem where to find a broker that’s reliable. Climbed on the boards and experienced in this organization gave me http://10binaryoptionsbrokers.org/ website it collected the best brokers and I’ve plumped for for myself Finpari.

Read Full Q/A … :
Unknown Printer

HP Designjet 750C+
ANSWER : I was replacing the belt on my 750c and let the y-axis motor slip out of my hand. This caused the two wire terminals to disconnect from the motor. Does anyone know which terminals the white and black wires attach to? One of the terminals has a red dot beside it and I assume this is an indicator, but do not know which wire connects there. Any help would be greatly appreciated.

Read Full Q/A … :
Unknown Printer

Rear Paper Feed Blocked On Left Side?
ANSWER : Most times it is something you can’t see, like a small torn scrap of paper. What you can try is to shove a file folder down the path the paper takes. That will push out any offending scrap without having to take the printer apart.

Read Full Q/A … :
Unknown Printer

Ink leak
ANSWER : opppssss, no attached picture.

Read Full Q/A … :
Unknown Printer

Printer doesn't print
ANSWER : http://h20564.www2.hp.com/hpsc/doc/public/display?docId=bpp03841#N1033E

Read Full Q/A … :
Unknown Printer

Part Search
ANSWER : Did you try partsnow?

Read Full Q/A … :
Unknown Printer

HP LaserJet 1160 pick-up problem
ANSWER : Take the black rubber roller out. Clean it and turn it 90-180 degrees so there is fresh rubber in the “corner”.

Read Full Q/A … :
Unknown Printer

ERROR 22.0.10
ANSWER : Ink delivery problem from the left ink station.

Read Full Q/A … :
Unknown Printer