Xerox WorkCentre XD105F

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

White lines will typically start appearing on your print outs due to a clogged up printer head. Your first port of call when solving this problem is to run the cleaning program on your printer, which should be accessible through its settings menu.
There are four primary causes for horizontal banding on prints from inkjet printers, (1) nozzle clogs, (2) mis-aligned print heads, (3) low quality print settings (4) incorrect paper thickness settings. Below we will describe each of these causes for horizontal banding as well as ways to try and fix them.
Streaks and unwanted lines could mean that the printer heads are out of alignment. There`s an alignment tool in the printer`s control panel. If that`s not the issue then the printer is dirty. Printer ink stripes may appear along the edges of the paper, which means there`s ink on the rollers and other parts.
Streaking is usually caused by a worn out drum unit or spent toner cartridge. Drum units are a consumable and only need to be replaced after the use of 3 or 4 toners. Not all printers use a separate toner and drum unit.
Vertical lines in prints are an early warning sign of a low ink cartridge, which may show up before the printer`s low ink alerts start. You can fix the problem by replacing the low cartridge. Gently shaking the drained cartridge a bit may help to get another few prints out of it without vertical lines.
Generally speaking, a visible vertical line down your page after printing is an indication that the image drum in the machine may be damaged. It could also mean that the machine is reaching the end of its life.
When your printer leaves black lines, the lines indicate that there are excess toner powders on the rollers or transfer belt within the printer. As the paper is moved along by the rollers and transfer belt, any excess powder left on them can result in lines being left on the paper.
If your image has diagonal streaks through it, your printer could have a creased ribbon. Creased ribbons are caused by uneven spacing pressure from the print head, inconsistent pressure, and incorrect loading.
The most obvious sign of low toner cartridge is poor print quality. Streaking, lines or missed prints are all possible signs that cartridge replacement is imminent. If you have tried rocking the toner cartridge and are still getting poor prints, it is likely time to replace your cartridge.
Also known as Provincetown printmaking, white line printmaking began in 1914 as an alternative to Japanese printmaking in which each color of the print has its own woodblock. American printmakers carved an entire design into one block, using the carved lines to separate areas that would have different colors.
What causes the spots? The usual cause is a dust particle that falls on or is stuck to the paper. Then as the paper runs through the printer, the ink gets laid on top of the particle instead of the paper surface. Eventually the particle falls off leaving a white spot where it blocked the ink.
White streaking through the printout or an entire missing color both indicate an empty cartridge. If the cartridge is depleted of one color, it needs to be replaced. Each color is necessary to create the colors used in day-to-day printing.
Horizontal lines are lines that run from left to right and are parallel to the x-axis. Vertical lines are lines that run up and down and are parallel to the y-axis.
A horizontal line is a straight line that goes from left to right or right to left. In coordinate geometry, a line is said to be horizontal if two points on the line have the same Y- coordinate points. It comes from the term “horizon”. It means that the horizontal lines are always parallel to the horizon or the x-axis.
This can be caused by debris or contamination on the drum, the transfer corotron, the device not positioned properly on a solid flat, level surface, or by using old or damp paper.
A cartridge may be running out of ink even if the graphic shows ink remaining (see the note at the start of this section). Lines or streaks always appear in printouts when the cartridges begin to run out of ink. Replace print cartridges that are out of ink or low on ink.
A printer printing lines on the page are normally caused by a blocked, dirty, or damaged print head. Blocked ink cartridge nozzles, or not removing protective seals correctly when you installed a new ink cartridge can also cause missing lines of print.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

How to reset page counter on Xerox Phaser 3160N
ANSWER : http://apexmic.info/how-to-reset-chip-xerox-phaser-3160.html

Read Full Q/A … :

Xerox WorkCentre XD105F

Xerox Phaser 3250 solid red light with no apparent reason
ANSWER : I found the problem to be a fuser. For $150 you can fix this issue. Cheaper to buy a new unit.

Read Full Q/A … :

Xerox WorkCentre XD105F

Xerox 6180: Can I force continued cartridge use?
ANSWER : There is no workaround to ‘fool’ the printer into continuing printing.

Read Full Q/A … :

Xerox WorkCentre XD105F

Xerox 7760 Wrong paper size error when trying to print to A4
ANSWER : At first you could try to print using the Multifunction/Bypass Tray on the left side of your printer.

Read Full Q/A … :

Xerox WorkCentre XD105F

Printhead Tilt Fault Error, Xerox 8870 Colorqube
ANSWER : The 8870 I had which had a 97,721.00 error ended up being a split\cracked gear on the shaft that engages the maintenance kit, the :9875 is the printer page count. You can try to rehome the process drive but I would check and see if there is a split gear (where it mounts on shaft) first because the shaft will spin but the gear won’t engage if it’s cracked or split so it throws an error.

Read Full Q/A … :

Xerox WorkCentre XD105F

Horizontal lines(light yellow)
ANSWER : i have printed around 300 sra3 sheets and 100 a4 on various grades of paper and there has been no difference.

Read Full Q/A … :

Xerox WorkCentre XD105F

Xerox Color Qube 8570 Error Code
ANSWER : From Service Manual

Read Full Q/A … :

Xerox WorkCentre XD105F

Xerox Phaser 7750 – FUSER delima
ANSWER : Thanks! On my printer, one of the magnets did dislodge and was stuck on the other side. I finally figured out what it was from your advice. The magnet was not broken and popped right back in to place. Keeping my fingers crossed that was the only issue.

Read Full Q/A … :

Xerox WorkCentre XD105F