Xerox Phaser 8560
How to Identify and Fix Common Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
It means there is an incorrect parameter in the paper size. This happens mostly with the wrong print driver in use, or when an application overrides the driver. So make sure it is the right print driver, and make sure that the Application is not set to an odd size.
024-747 The specified combination of parameters (stored file size, paper size, paper tray, duplex command, output tray) cannot be executed or continued. Load Paper in Trays 1-4. Make sure that the paper size, paper tray, duplex settings, and output tray settings are correct for the job.
Most probably it is related to misconfiguration the settings of permissions. Usually, it happens when a bad Windows update got installed on your computer. Sometimes, it happens due to corrupt the printer driver.
The issue is due to a recently expired certificate included with the device firmware. The loss of this communication means that the meter reads, supplies replenishment information and maintenance information has stopped being transmitted and reported.
If your printer`s status displays “Printer in error state,” there may be a problem with the printer itself. Make sure the printer is turned on and connected to your PC by Wi-Fi or cable. Check it for low paper or ink, and be sure the cover isn`t open and the paper isn`t jammed.
Operation could not be completed (error 0x00000709). Double check the printer name and make sure that the printer is connected to the network. This error mainly occurs when more than one printer is connected to a computer. It may also occur when a printer is shared over a network.
a misprint or misspelling in a text.
Fault Code 016-758: The Account is not Authorized for Color Printing or Copies. This Error Indicates Only Allows Printing in Black and White, Color Printing is Restricted.
Fault Code 059-324: Fuser Under Temperature.
Fault Code 059-324: Fuser Under Temperature.
Re: Phaser 6510 error code 124-315 After Power Cycling
Usually this problem only occurs if the NVRAM has been reset or the engine board has been replaced without backing up the NVRAM.
With just a few simple steps, your multifunction printer is ready to scan or print directly to or from the cloud. 2 Scan to Email, FTP, Network or somewhere more down to earth — like the integrated front and rear panel USB ports. Easy management.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Xerox Phaser 3250 solid red light with no apparent reason
ANSWER : I found the problem to be a fuser. For $150 you can fix this issue. Cheaper to buy a new unit.
Read Full Q/A … :
Xerox Phaser 8560
Xerox 7760 Wrong paper size error when trying to print to A4
ANSWER : At first you could try to print using the Multifunction/Bypass Tray on the left side of your printer.
Read Full Q/A … :
Xerox Phaser 8560
How to reset page counter on Xerox Phaser 3160N
ANSWER : http://apexmic.info/how-to-reset-chip-xerox-phaser-3160.html
Read Full Q/A … :
Xerox Phaser 8560
Phaser Jams every time code: 0,006.74
ANSWER : http://www.support.xerox.com/support/phaser-8560mfp/support/enus.html
Read Full Q/A … :
Xerox Phaser 8560
Xerox Phaser 7750 – FUSER delima
ANSWER : Thanks! On my printer, one of the magnets did dislodge and was stuck on the other side. I finally figured out what it was from your advice. The magnet was not broken and popped right back in to place. Keeping my fingers crossed that was the only issue.
Read Full Q/A … :
Xerox Phaser 8560
xerox phaser 6100
ANSWER : This post is from nearly a decade ago, so don’t know if the thread is still active. I have this printer in my rural WV classroom and am searching for a fuser unit for the Phaser 6100. Anybody know where I can still purchase one ?
Read Full Q/A … :
Xerox Phaser 8560
Error Code 51.1 says Printer Error No Kidding.lol
ANSWER : Sometimes turning off and on will allow you to print a few pages. The error is a beam detect error. The only real fix is to replace the laser scanner unit. Could be a loose connector on the scanner or DC controller from the scanner. That’s unlikely. You could try the only other free fix which is to open the scanner assy. and clean all the mirrors inside. The dust could obstruct the laser beam enough to cause the detect error.
Read Full Q/A … :
Xerox Phaser 8560
Printer error Oxc18a0201
ANSWER : Have no idea what model you have, but try this forum post or search through the site using your model and error.
Read Full Q/A … :
Xerox Phaser 8560