Xerox Phaser 8500

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

It means there is an incorrect parameter in the paper size. This happens mostly with the wrong print driver in use, or when an application overrides the driver. So make sure it is the right print driver, and make sure that the Application is not set to an odd size.
024-747 The specified combination of parameters (stored file size, paper size, paper tray, duplex command, output tray) cannot be executed or continued. Load Paper in Trays 1-4. Make sure that the paper size, paper tray, duplex settings, and output tray settings are correct for the job.
This fault indicates that the fuser is in an overheat condition and the fault needs to be reset by the technician. Contact Support for additional assistance.
Error 1003 (Field out of label) is displayed when one or more fields are placed outside of the label dimensions defined in the printer. The error can be caused by: The page dimensions defined incorrectly in the software. The software not transmitting the page dimensions to the printer.
Replace the Fuser Cleaning Web Cartridge. If the problem persists, contact Support for additional assistance.
043-343 A YMC Link Sensor detection error was detected (Mismatch of print mode and YMC Link Sensor driven state register information). WARNING: Ensure that the electricity to the machine is switched off while performing tasks that do not need electricity. Refer to GP 10. Disconnect the power cord.
If necessary, contact Support for additional assistance.
The issue is due to a recently expired certificate included with the device firmware. The loss of this communication means that the meter reads, supplies replenishment information and maintenance information has stopped being transmitted and reported.
a misprint or misspelling in a text.
The issue is due to a recently expired certificate included with the device firmware. The loss of this communication means that the meter reads, supplies replenishment information and maintenance information has stopped being transmitted and reported.
Most of the issues with non printing jobs and „Offline” messages are from driver settings. First check to see if there is no job in the print queue (delete any job if exist). Check the port to be on TCP/IP and not WSD. MS convert the port to WSD.
Re: Phaser 6510 error code 124-315 After Power Cycling

Usually this problem only occurs if the NVRAM has been reset or the engine board has been replaced without backing up the NVRAM.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Xerox Phaser 7750 – FUSER delima
ANSWER : Thanks! On my printer, one of the magnets did dislodge and was stuck on the other side. I finally figured out what it was from your advice. The magnet was not broken and popped right back in to place. Keeping my fingers crossed that was the only issue.

Read Full Q/A … :

Xerox Phaser 8500

Xerox 7760 Wrong paper size error when trying to print to A4
ANSWER : At first you could try to print using the Multifunction/Bypass Tray on the left side of your printer.

Read Full Q/A … :

Xerox Phaser 8500

How to reset page counter on Xerox Phaser 3160N
ANSWER : http://apexmic.info/how-to-reset-chip-xerox-phaser-3160.html

Read Full Q/A … :

Xerox Phaser 8500

Xerox Phaser 3250 solid red light with no apparent reason
ANSWER : I found the problem to be a fuser. For $150 you can fix this issue. Cheaper to buy a new unit.

Read Full Q/A … :

Xerox Phaser 8500

xerox phaser 6100
ANSWER : This post is from nearly a decade ago, so don’t know if the thread is still active. I have this printer in my rural WV classroom and am searching for a fuser unit for the Phaser 6100. Anybody know where I can still purchase one ?

Read Full Q/A … :

Xerox Phaser 8500

Old printer cable
ANSWER : The do sell adapter cables at Fry’s Electronics. You can search their site if you don’t have a store near you.

Read Full Q/A … :

Xerox Phaser 8500

Error Code 51.1 says Printer Error No Kidding.lol
ANSWER : Sometimes turning off and on will allow you to print a few pages. The error is a beam detect error. The only real fix is to replace the laser scanner unit. Could be a loose connector on the scanner or DC controller from the scanner. That’s unlikely. You could try the only other free fix which is to open the scanner assy. and clean all the mirrors inside. The dust could obstruct the laser beam enough to cause the detect error.

Read Full Q/A … :

Xerox Phaser 8500

error code :91,720,00:60960
ANSWER : Xerox 8570 Error Code 91720

Read Full Q/A … :

Xerox Phaser 8500