Xante Accel-A-Writer 8100
How to Identify and Fix Common Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
Dust, paper fiber, and other debris might accumulate on the paper feed rollers and cause paper jams and paper feed issues. Clean the rollers inside the printer, and then try to print again. Turn off the printer, and then disconnect the power cord.
your pickup roller is dirty and the printer can`t grab a piece of paper. it will say paper jam when it does this. get a drop of dishsoap and clean the pickup roller of your printer with this. scrape at it with your fingernail to get the roller clean and wipe it off with a damp washcloth.
A good way to stop the printer becoming jammed, is to fan the paper before you put it in the tray as this will shake out any dust and reduce static, which are two major causes of paper jams. Another way to avoid a printer paper jam is to keep your machine clean.
If your printer keeps jamming, you should know that the most common cause of a jam is misalignment of the paper. Paper needs to load in smoothly, completely flush with the tray. Overfilling the tray is a great way to ensure you will be spending some personal time getting to know the inside of a printer.
A paper jam is when paper or other printed material gets stuck or lodged in a printer and cannot eject.
The guides in the paper tray are there to make sure the stack of paper is exactly where the printer was designed to grab from. If the paper is even slightly askew, the rollers will pick it up a little crooked, and — guess what — the crooked sheet will immediately get jammed.
Low-quality paper leaves an accumulation of tiny paper bits often referred to as “paper dust” inside the machine. This “dust” is one of the top causes of paper jams. More dust means more jams. Besides jams, the dust also contributes to poor-quality prints and causes machine parts to wear at a faster rate.
Slide the paper all the way into the printer. The leading edge of the paper will stop at the Paper Drive Roller. Locate the Paper Sensor/OOPs sensor on the right side of the paper path. It can be seen from the top of the printer with the Top Cover open and has red, black, and blue wires attached to it.
Clear jammed paper from the input and output tray
Press and hold the two buttons on both sides of the output tray to move out the output tray from the printer. Pull out the input tray. For HP OfficeJet Pro 9020 printers, also pull out Tray 1. Gently remove any jammed paper from the area.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.
ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.
Read Full Q/A … :
Xante Accel-A-Writer 8100
Canon mx410 Paper jam message, but no paper jam?!
ANSWER : I have exactly the same problem, no answers 😳
Read Full Q/A … :
Xante Accel-A-Writer 8100
Paper Jam error but no paper jam
ANSWER : Obviously you didn’t get all the paper cleared out. There is a small scrap in the paper path causing the jam when the paper hits it. You can try clearing it out by inserting something stiff like a piece of file folder from the back of the printer into the paper path and pushing the offending piece out that way.
Read Full Q/A … :
Xante Accel-A-Writer 8100
Paper Jam and carriage jam code when nothing is jammed
ANSWER : Did you try cleaning the encoder strip that runs through the cartridge assy.? Use Window Cleaner on a paper towel. Also, check inside on the right. I’ve seen a lot of times where there is a folded up scrap of paper that stops the carriage from going all the way to the right.
Read Full Q/A … :
Xante Accel-A-Writer 8100
hp 8600 pro when power on, paper jam message appear but there is no paper jam in the tray
ANSWER : Hp 8180 Photosmart All In One code keeps says paper jam and carriage jam when neither are jammed. I followed all the recommended things to do. I live in Raleigh NC any place to take this or any suggestion.
Read Full Q/A … :
Xante Accel-A-Writer 8100
Paper jam in tray 2 (but no paper pulled from tray) also M476DN models
ANSWER : Isopropyl alcohol is not recommended for rubber rollers. It dries out the rubber and hasten it’s cracking and breaking. It will do nothing to restore the grip. Those rollers are really hard to replace. It would be easy if that dumbass secondary menu really worked. None of the techs I’ve spoke to ever got into it. Everyone I know sends a print job and listens for the roller to rotate into position where you can pull it off.
Read Full Q/A … :
Xante Accel-A-Writer 8100
Keep getting a paper jam message. There is no jam.
ANSWER : You can quit wondering. Parts are unavailable. I’ve seen posts where people have 3D printed the parts or machined them out of metal.
Read Full Q/A … :
Xante Accel-A-Writer 8100
message error: ADF paper jam
ANSWER : There is a thin plastic arm that the paper pushes on. It is spring loaded. If it doesn’t return and unblock the sensor after the paper passes it, you get the paper jam warning. I’m guessing that is the spring you are referring to.
Read Full Q/A … :
Xante Accel-A-Writer 8100