HP DeskJet 3650

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

You need to ensure your HP printer has enough paper, ink, or toner, and it is not stuck on paper jam. Also, check the status of your printer cartridge and try replacing it with a new one if it is not good enough. In some cases, your HP printer stops printing after you replace its parts.
Restart your printer, router, and mobile device

Restart all devices to clear network and hardware error states. Turn off the printer, and then turn it on again. Disconnect the power cable from the router, wait ten seconds, reconnect the cable, and then wait for the internet connection to complete.

Make sure your Wi-Fi network and printer setup meet connection requirements. Restart the printer and the computer or mobile device to clear possible error conditions. Make sure the printer is not connected to a computer with a USB cable.
Reasons why your HP printer has ink but won`t print

This may seem obvious, but it sometimes happens: first make sure your paper tray has paper in it. Misalignment, clogged printheads, faulty data communication or insufficient ink levels can also be sources of the problem.

To answer the actual question of why you can`t print it could be due to simple things such as networking issues, a paper jam, or low toner ink. Or it could be more complicated, such as service is required, there`s a physical breakage, or there`s a hardware driver problem.
If your printer is running low on ink, it may start printing blank pages. To check your ink levels, go to your printer`s control panel and select the Ink Levels option. Whenever the ink levels are low, replace the cartridges with new ones. You can also try shaking the cartridge gently to redistribute the ink.
Do a hard reset on your printer. To do this you just need to turn off your printer, unplug for a few minutes and then plug the printer again. If that still doesn`t work, try turning the printer and your computer off, and then start it back up again. Try uninstalling and then reinstalling your printer driver.
On your client computer, open the Devices and Printers by pressing the windows key and go to Control Panel > Devices and Printers. Right-click the printer you want to manually enable and click Printer Properties.
If your HP printer not printing black ink correctly, here`s what you should do. Using non-genuine ink cartridges. Printheads that have become clogged. Ink cartridges that are defective or empty.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.
ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.

Read Full Q/A … :

HP DeskJet 3650

when printing front and back, the front will print well but the back will fade
ANSWER : It happens because second side voltage is much higher and the board breaks. Are you getting this issue in auto duplex only, or same error you are getting when you print second side manually?

Read Full Q/A … :

HP DeskJet 3650

Print file sent but no printing occurs
ANSWER : Been working on these since they first were released. Never seen a problem like yours. If it happens again, try doing an engine test, as it bypasses the formatter board. The engine test is located at the right side of the manual tray opening. Look for a hole in the side wall. Stick something like a paper clip into it to actuate the test button. It will then print a lined test page. If it does that, then it points to the formatter board as the cause of your problem.

Read Full Q/A … :

HP DeskJet 3650

Prints blank pages, won't print from computer
ANSWER : Don’t know why you replaced the fuser, but assuming you had print before, then it must have been something you did during the procedure. Only thing I can suggest is to recheck your work. Just because you reinstalled a connector doesn’t mean that it is seated firmly enough to work. Any flat ribbon connectors that you removed and reinstalled, check to see that the contacts are all flat and not peeled back.

Read Full Q/A … :

HP DeskJet 3650

Epson Artisan 835 print head cleaning question
ANSWER : I had the same problem. After reading the comments, I tried Liquid Wrench spray. 1st try got about sixty percent improvement. Tried again this time I let it set for about 10 min then did a head cleaning. Completely solved the problem. I am a little concerned about its use on plastic. So far so good.

Read Full Q/A … :

HP DeskJet 3650

HP Deskjet 640c wont print??
ANSWER : yes

Read Full Q/A … :

HP DeskJet 3650

My printing come out blurred
ANSWER : doris…There are usually 2 reasons for blurry output on this printer. First, make sure that the alignment is correct. You can get to it from the maintenance tab on the software that came with the printer. The other common cause of blurring is debris under the printhead. Hope this helps.

Read Full Q/A … :

HP DeskJet 3650

problems with printing
ANSWER : Check your settings to make sure they are Left to Right print order. If they are then reinstall printer driver. If that doesn’t correct problem uninstall printer, reboot computer, and reinstall printer.

Read Full Q/A … :

HP DeskJet 3650