HP Color LaserJet 4550
How to Identify and Fix Common Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
If one or more toner cartridges are installed incorrectly, this may result in a 54.2 carousel rotation error. This error is typically accompanied by a loud grinding noise. NOTE: The carousel is the rotating part under the top cover to which all four print cartridges attach.
In general, a 49 service error is a situation where the printer cannot process a file that has been sent. In some cases the file is corrupted and in other cases the printer`s firmware simply cannot interpret that file.
When a 50.4F. 00 error is displayed on the control panel, it indicates that there is an issue with the fuser or the power outlet where the printer is connected.
A 49 error typically occurs when the printer attempts to perform an action that the firmware is not capable of performing or might not be designed to handle, for example: Printing files that include unsupported printer commands. Interfacing with a third-party solution that was not designed to work with the printer.
There can be a motor error in your printer. If the Electronic transfer belt (ETB) in your printer is missing this error can crop up. If the Electronic transfer belt (ETB) is incorrectly installed in your printer.
This error might happen at any time for multiple reasons. The most common causes are due to the printer being asked to perform an action that the firmware is not capable of, and might not have been designed to perform, such as: Printing files with unsupported programming commands.
Description: Printer boots up to 59. F0 Error and is unable to print. This error is primarily caused by one of the following conditions: A transfer alienation failure in which the ITB is stuck and unable to properly engage the internal transfer rollers.
The 50.2 fuser error message is a “Slow Fuser” error, which is a time-out error where the fuser is not warming up fast enough. If you see the error message “50.2 Fuser Error” on your HP Color LaserJet 2820 or 2840 series printer, you probably need to replace the fuser.
Look inside the fuser opening to make sure there is no debris or jammed paper. Remove any debris or jammed paper, if found. Hold the handles on each side of the fuser and reinstall it in the printer.
The printer experienced a black drum motor M3 error. 59.05. 50 Black drum motor startup abnormality.
41.2 Error Code on HP Laser Printers
The arcing occurs in the toner/transfer area, and can be caused by a defective toner cartridge, bad high voltage or ground connections to the toner cartridge or transfer roller, or a defective high voltage power supply.
The 59.40 is a “fuser rotational error“. Meaning the fuser was unable to rotate causing this error.
A product error has occurred where a memory tag CPU error was detected, or there is a problem with the air sensor or power supply. 58.04 = check low-voltage power supply (ECU) Make sure the line voltage and current source meet the electrical specifications for the product. To resolve problems with the power supply: 1.
This code indicates the disconnected status of your HP printer. Here are solutions you can try to fix this. 1. Reconnect the printer and then reinstall the printer driver.
A 49 error typically occurs when the printer attempts to perform an action that the firmware is not capable of performing or might not be designed to handle, for example: Printing files that include unsupported printer commands. Interfacing with a third-party solution that was not designed to work with the printer.
59.10 is a main drive error, which could be a bound up fuser. 51.10 is a laser error, which could be a bad laser unit. Which error do you have? If the printer can print an engine test, then you may have a bad formatter.
59.70 is a black developer motor failure. If unit is still under warranty contact tech support and get it repaired. If unit is out of warranty you will need a developer motor RM2–7344–000CN.
Description: This error is primarily caused by a transfer alienation failure in which the ITB is stuck and unable to rotate, the SR9 sensor (the primary transfer roller disengagement sensor) has gone bad or the fuser drive assembly has failed.
Dial-up connection error 756 is caused when the dial-up connection that is being initiated is already begin dialed. This can be caused by redial of previous unsuccessful dial-up attempt. To fix dial-up connection error 756, try to disconnect the connection through AT Command Tester and retry connecting again.
Error code 7 means there is not enough memory available, To resolve this issue you would need to increase the memory on the endpoint, if that is not possible using an offline cab file should allow the endpoint to patch.
This error might happen at any time for multiple reasons. The most common causes are due to the printer being asked to perform an action that the firmware is not capable of, and might not have been designed to perform, such as: Printing files with unsupported programming commands.
A 49.38. 0C indicates an internal firmware error has occurred. The root cause of this can vary depending on the version of firmware running on the device. Knowing what version your HP LaserJet CP5525 is running would help us in diagnosing the issue.
Error 0x0000011B is a common issue on Windows systems and can have various causes. Here are the most common causes and how to resolve them: Driver conflict: This happens when two drivers access the same resources at the same time. To resolve this issue, check for any conflicting drivers and update or disable them.
The 51.01 and 51.1 errors are fairly common error codes on the HP LaserJet 4100, 4100N, 4100TN, and 4100DTN series printers. This error indicates a failure with the laser scanner assembly, which is a high-failure part on these models.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Error Code 51.1 says Printer Error No Kidding.lol
ANSWER : Sometimes turning off and on will allow you to print a few pages. The error is a beam detect error. The only real fix is to replace the laser scanner unit. Could be a loose connector on the scanner or DC controller from the scanner. That’s unlikely. You could try the only other free fix which is to open the scanner assy. and clean all the mirrors inside. The dust could obstruct the laser beam enough to cause the detect error.
Read Full Q/A … :
HP Color LaserJet 4550
HP Color LaserJet 4550 Streaking
ANSWER : hello,
Read Full Q/A … :
HP Color LaserJet 4550
Error Code 52.1M
ANSWER : Magenta laser error. The spinning motor bearings cause the squeal and that slows it down causing the error. You could try opening it and lubricating the motor shift with a drop of synthetic lubricant. Do not use more than a drop.
Read Full Q/A … :
HP Color LaserJet 4550
HP CLJ CP 5225 ERROR 55.0601
ANSWER : my printer cp5225 is giving me error code 55.0601 message which i can’t fix please help
Read Full Q/A … :
HP Color LaserJet 4550
Error Message 4F on MFC 210C
ANSWER : Basically this kind of error caused by loss of voltage on print head. If this is the case then I suggest to buy a new printer rather than replace print head. Print head might be too costly.
Read Full Q/A … :
HP Color LaserJet 4550
HP 9040 MFP Error code
ANSWER : bonsoir
Read Full Q/A … :
HP Color LaserJet 4550
Scanner error keeps coming up
ANSWER : I am having the same problem with my Epson Workforce 645
Read Full Q/A … :
HP Color LaserJet 4550
Density Shutter Error
ANSWER : I’ve never worked on one of those printers, but I have never, ever seen 1 valid solution for printer repair on fixya.com I read the replies there when I need a good laugh. Makes me wonder what the “techs” on that forum actually do for a living. It certainly couldn’t be printer repair.
Read Full Q/A … :
HP Color LaserJet 4550