Canon Color Bubblejet (BJC) S500
How to Identify and Fix Common Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
If there is plenty of ink and the printer does not print, clean the Print Head then print the nozzle check pattern to ensure ink is ejected properly. If the problem is not resolved after performing Print Head Cleaning twice, carry out the Print Head Deep Cleaning.
This error occurs due to the chip on your cartridge still reporting a low or empty ink level from its previous use. The chip itself cannot be reset, so when the cartridge is refilled and then installed into a new machine it will still register as empty.
If your Canon printer isn`t recognising a compatible ink cartridge, this may be because the data on the cartridge chip is stamped with an empty status before it was remanufactured. Hold down the stop / cancel button for 5 seconds to bypass the `ink has run out` message and your cartridge should work.
Issue. When the message “Ink absorber full.” is displayed, the printer stops printing and needs ink absorber replacement. Push the power button to turn OFF the printer, and then contact the service center for replacement. Request either Canon or the dealer you purchased the machine for a repair service.
There are chips inside the original cartridges to record how many pages were printed and they cannot be reset. As a result the printer reads the chips and tells you that the cartridges are empty, even though they are not. This is why you are getting the “ink low” message even though the ink tank is at full capacity.
First, check your printer settings on the file or picture your trying to print. If your page is setup to print in “grayscale” it will only print in black and white. Change the setting to “default” so it will print in color. If your settings look good from the start, the cartridge may just need to be primed.
Here are the most common causes of a printer printing faded text or images: Low ink or toner levels. Toner sticking to the fuser roller or problems with the transfer roller. Low ink or toner density settings.
Although, if performed by a professional and with the right equipment, you can expect high-quality printing. Cartridge breakdown – You can only refill your cartridge up to five times.
Just above the circuit board on most printer cartridges, you`ll find a small button. You`ve seen these tiny buttons before on cell phones, phone chargers, etc. This is your reset button, and the only way to get in there is either with a paper clip or the tip of a pen (which will leave a tiny ink smudge on the button).
Printing with an empty cartridge will soon cause printhead nozzles to overheat and fry remaining ink solid.” So, if you must continue to print, use the “Printing Preferences” dialog, on the “PAGE SETUP” tab, with the “PRINT OPTIONS…”, “Print With:” option: “All Colors (Default)”, “All except PGBK (Black)”, or “Only …
When the printer asks you to disable detection, press and hold the Stop button for at least 5 seconds before releasing it. On that color, ink level detection will now be disabled. It will be your obligation to periodically check the cartridges and refill them well before they are empty.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
MP170 (5b00) Ink Tank Full Error
ANSWER : Thanks, worked a treat!
Read Full Q/A … :
Canon Color Bubblejet (BJC) S500
Full Ink Tank in Canon Pixma ip4000
ANSWER : It had been exactly the same subject, could not find an appropriate broker and process for earnings finally had to rummage through the Web, and there I came across this page http://optioninvest.org .Possibly you’ll find there is a therapy to your condition, thanks for the fascination!))
Read Full Q/A … :
Canon Color Bubblejet (BJC) S500
MP390 Waste ink tank full.
ANSWER : Thank you very much. Followed the reset and alarm light instructions and works great! Saved at least $100 service fee and/or replacing our printer.
Read Full Q/A … :
Canon Color Bubblejet (BJC) S500
Canon MP600 uses color ink to print black and white…
ANSWER : Have you tried setting the print out to grayscale only (black and white)?
Read Full Q/A … :
Canon Color Bubblejet (BJC) S500
ip4200 INK TANK RESET and WASTE TANK RESET
ANSWER : Different cartridges, notwithstanding, don’t have a ‘fill gap’ so you’ll have to make one yourself. Our refill units for these sorts of cartridges accompany a smolder apparatus which is utilized to blaze (really dissolve) a fill opening in the cartridge . Our refill guidelines will demonstrate you precisely where to make the fill opening (you would prefer not to make it in the wrong spot). A blaze device come standard in all refill packs for cartridges without processing plant made fill openings. if you want to get proper detailed information then call us at 1-888-924-2961for more information regarding canon printer support.
Read Full Q/A … :
Canon Color Bubblejet (BJC) S500
Ink Tank Cannot Be Recognized(Canon mp500)
ANSWER : My MX922 ran out of yellow (slowly) then didn’t recognize first one and then a second new Canon CLI-251 yellow cartridge. I’ve always used Canon. Then I inserted a 251a Y (extra large) yellow, and it worked immediately – for how long, I don’t know. Guess I’ll order another set of XL ink tanks – either that or a new printer.
Read Full Q/A … :
Canon Color Bubblejet (BJC) S500
Canon pixma – ink absorber almost full
ANSWER : They are on the bottom of the printer. If you want to clean them, you can take them out and wash them in hot tap water. Wring them out like a sponge. You will need to reset the printer. http://jezpinions.blogspot.com/2012/03/canon-mg6150-ink-absorber-reset-error.html
Read Full Q/A … :
Canon Color Bubblejet (BJC) S500
Canon Pixma iP3000 "Open door" Error code.
ANSWER : Look for a protruding plastic on the top that goes into an indentation. Mine was in the front left side. Put a piece of cardboard into the indentation.and close the door. The top plastic piece is not pushing the door close sensor down and because its too short and the cardboard allows the sensor to be reached and pushed.
Read Full Q/A … :
Canon Color Bubblejet (BJC) S500