HP LaserJet 3
How to Identify and Fix Common Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
yz Fuser error To continue turn off then on is displayed on the control panel, it indicates that there is an issue with the fuser. The XX and YZ are two digit codes that provide information on the specific issue causing the error. Press the power button to turn the printer off, and then back on to clear the error.
00 Fuser error indicates you have an actual fuser failure and the fuser needs replacing. Fusers are a consumable part and they are the main component in a printer maintenance kit; it is expected over the life of the printer you will replace the maintenance kit several times.
Error 50.8 suggests one end of the fuser is not heating up which may be damage to the sleeve or heavy media.
A high fuser temperature error has occurred. Note: A fuser error might occur because of inadequate power supply, inadequate line voltage, or a fuser problem.
Error 50 is Invalid destination number.
If you are experiencing a “50.7” fuser error, first turn the printer off and back on. Sometimes the error will temporarily go away with a reboot so you can print a few more pages, but usually the error reappears.
50.AF is a low fuser temperature error and usually caused by a defective fuser. Resetting the printer is unlikely to resolve this error.
50.2 error indicates that the printer is not heating up fast enough. This can be caused by a bad heating element in the fuser but can also be caused when the printer does not have adequate power due to overloaded circuits or being plugged into a power strip or surge bar that limits current flow.
If you see this error code 50.5 on an HP LaserJet 4200, 4240, 4250, 4300, or 4350 series printer, the fuser installed in the printer is registering as an incorrect fuser for that model printer.
The message `Fuser Error` or `Self-Diagnostic` means either the fuser has reached the maximum temperature allowed or there has been an error in detection of the correct temperature during specific times of the printing process.
When a 50.22. 00 or a 50.22. 11 error displays on the control panel, it indicates an issue with the fuser warming up.
Error 50.2 suggests the fuser can`t heat up properly. This might be fuser failure but could also be a power supply issue. Plug the printer directly into a wall socket, not into an extension. Try turning off, wait 20 minutes then on again.
The BCCode 50 usually occurs after the installation of faulty hardware or in the event of failure of installed hardware (usually related to defective RAM).
Just find the menu “APN setting” and re initialze it. Reboot. Then, it should work. If not, you`ll have to see with your carrier.
The 50.1 fuser error message refers to a low temperature reading on your fuser. If you see the error message “50.1 Fuser Error” on your HP Color LaserJet 2820 or 2840 series printer, you probably need to replace the fuser. Fusers are a consumable part and are sold as part of a maintenance kit.
If you are seeing a “50.1 Fuser Error” on your HP LaserJet 5000 or 5100 series printer, you probably need to replace the fuser. Fusers are a consumable part and are sold as part of a maintenance kit; it is expected over the life of the printer you will replace the fuser several times.
This is accomplished by the fuser lamp. The lamp operates at 120VAC or 250VAC and is typically rated at 500W to 600W. The control signal from the heater control circuit is typically low voltage (< 9VDC).
A fuser unit is a pair of heated rollers within the printer that fuses the toner onto the paper being printed on. Toner particles are pulled to the paper to create the desired text and images as the paper passes the imaging drum.
The Fuser is the piece that fixes the toner on the paper. This, like any other consumable part, wears out with the regular use of prints, since it is one of the components that suffers the most due to its mechanical wear and overheating of its components, due to the high temperatures it must withstand.
On the HP LaserJet P3015 P3015n and P3015dn series printers, this 51.00. 10 error code may be temporary. Try turning the printer off and back on to see if the error clears. If the error comes back repeatedly, you have a failing laser scanner assembly which requires replacement.
The printer experienced a black drum motor M3 error. 59.05. 50 Black drum motor startup abnormality.
a 52 Scanner error indicates the laser/scanner which writes the image to the drum has malfunctioned. This is a hardware error and most times the actual laser/scanner assembly needs to be replaced.
The laser/scanner assembly needs to be replaced as one of the motors has gone bad inside the assembly.
Any of these error codes (51.20 51.21 51.22 51.23) points to a failure with one of the laser scanner assemblies on the HP Color LaserJet 4610 an 4650 series. To solve these error codes, replace the corresponding laser scanner.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
error 50
ANSWER : Most likely the quartz lamp in the fuser assy. burned out. you can remove it and check the resistance on the 2 large pins in the connector. Should be several ohms.
Read Full Q/A … :
HP LaserJet 3
can i override the error code 50
ANSWER : First off, your printer is an inkjet printer. It has no drum. The error refers to a paper jam.
Read Full Q/A … :
HP LaserJet 3
Error Code 51.1 says Printer Error No Kidding.lol
ANSWER : Sometimes turning off and on will allow you to print a few pages. The error is a beam detect error. The only real fix is to replace the laser scanner unit. Could be a loose connector on the scanner or DC controller from the scanner. That’s unlikely. You could try the only other free fix which is to open the scanner assy. and clean all the mirrors inside. The dust could obstruct the laser beam enough to cause the detect error.
Read Full Q/A … :
HP LaserJet 3
Error Code 52.1M
ANSWER : Magenta laser error. The spinning motor bearings cause the squeal and that slows it down causing the error. You could try opening it and lubricating the motor shift with a drop of synthetic lubricant. Do not use more than a drop.
Read Full Q/A … :
HP LaserJet 3
Error Message 4F on MFC 210C
ANSWER : Basically this kind of error caused by loss of voltage on print head. If this is the case then I suggest to buy a new printer rather than replace print head. Print head might be too costly.
Read Full Q/A … :
HP LaserJet 3
HP 9040 MFP Error code
ANSWER : bonsoir
Read Full Q/A … :
HP LaserJet 3
HP CLJ CP 5225 ERROR 55.0601
ANSWER : my printer cp5225 is giving me error code 55.0601 message which i can’t fix please help
Read Full Q/A … :
HP LaserJet 3
Scanner error keeps coming up
ANSWER : I am having the same problem with my Epson Workforce 645
Read Full Q/A … :
HP LaserJet 3