HP DesignJet 130NR

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

check the belt condition and clean encoder strip. Turn on without the maintenance cartridge > if there is still 21:13 error and the carrige is not able to move freely not gettign struck on the right side. issue could be a faulty service station > Replace it.
If the paper does not load, the leading edge of the paper may not be straight or clean and needs to be trimmed. Remove the initial 2 cm (1 in) from the roll and try again. This may be necessary even with a new roll of paper. Ensure the roll ends are tight against the spindle ends.
Sometimes the service station is stuck in cycle and you will not be able to even move the carriage assembly. Most times with this error the service station needs to be replaced, but it could be other items.
Very often a 13.1 Paper Jam Message will appear, instructing the user to check Tray 2 or to check under the toner cartridge. Upon thoroughly checking the printer there is no paper jam to be found anywhere.
A 13. FF. FF error is related to jams in the paper path. These errors indicate that the product powered up with a jam.
Turn the product on while you press and hold the Resume button for 10-20 seconds. The Attention light turns on. Release the Resume button. The Attention and Ready lights cycle while the product restores factory defaults.
Remove the stack of paper from the tray. Check for obstructions inside the tray. Use a flashlight to view the mechanism inside the tray to make sure that nothing blocks the paper from engaging with the rollers. Even small pieces of paper can cause paper feed issues.
When a 31.13. 13 error appears on the control panel, it indicates that there is a jam in the document feeder because the feeder cover is open. Open then close the document feeder cover. If issue remains, open the document feeder cover.
When a 13. E1. D2 Error appears on the control panel, it indicates there is jam because the paper cannot exit the printer. This might be caused by damage to the output bushing.
It may happen that the cutter is blocking the carriage over the service station, preventing the service station from performing the movement correctly. The cutter is on the left side of the carriage. Perform the Service Station diagnostic test to troubleshoot the problem further. Replace the Service Station.
That error code indicates a failure of the yellow laser scanner. Unplug and leave for a few minutes, also make sure you are plugged directly into the wall and not into a surge protector.
Hope you are well, usually that error message stands for paper jam inside the printer, please check the rear door, remove the tray 2 and check for paper stuck.
That error code indicates a failure of the yellow laser scanner. Unplug and leave for a few minutes, also make sure you are plugged directly into the wall and not into a surge protector.
ERROR 21 11 – PROBLEMA CON LA SERVICE STATION DEL PLOTTER

Solución error 21:11: sustituir la service station (limpiar service y comprobar todos los contactos del plotter). Si necesita que un técnico especializado repare su plotter le ofrecemos un servicio in situ para que no tenga que mover su plotter.

13 – Paper Jam

If this code appears you have a paper jam, newer models of HP printers will tell you where the jam is located so you can just follow the instructions on the screen to resolve the error code.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Reset maintenance kit
ANSWER : Press “2” & “6” keys on the numpad during startup. Key kombinations have changed a few years ago.

Read Full Q/A … :

HP DesignJet 130NR

Brother MFC-L2740DW maintenance mode
ANSWER : Hi,

Read Full Q/A … :

HP DesignJet 130NR

maintenance menu / mode on Brother MFC L2740DW
ANSWER : Hi,i have a “brother” 2720 and i enter the maintenance mode: You have to press first scan/copy/fax, then the home button lights up on the right. Now press the home button until you see a screen with 4 squares in the first two one is the serial number and firmware. Now press the last square until you get a keyboard. Now you can press the *2864 and you are in maintenance mode.

Read Full Q/A … :

HP DesignJet 130NR

M806 replace maintenance kit
ANSWER : Have you tried to see if there’s a reset maintenance kit from the menus ?

Read Full Q/A … :

HP DesignJet 130NR

Perform Printer Maintenance Message
ANSWER : You can just wait until you have problems. Replace the pickup/sep rollers when you have jamming problems. Replace the fuser when you have spots or lines on the page. Transfer roller doesn’t really need replacing.

Read Full Q/A … :

HP DesignJet 130NR

Brother HL-4040 CDN Maintenance 4
ANSWER : I turned off the machine and restarted it. Problem solved. “Maintenance 4” message was replaced with “Ready”.

Read Full Q/A … :

HP DesignJet 130NR

reset maintenance tank
ANSWER : Ruthijean…Performing a reset is only part of the solution. The waste ink pads which line the bottom of the case should be cleaned or replaced. To reset the maintenance counter do the following:

Read Full Q/A … :

HP DesignJet 130NR

Oki maintenance software
ANSWER : Try this link for the Maintenance Manual of the OKI-C511dn; I’m searching for MuWin.exe too… 😉

Read Full Q/A … :

HP DesignJet 130NR