Epson EPL 7000

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Make sure your paper meets the specifications for your product. If paper dust builds up on the rollers, they may lose traction and become unable to feed paper properly. Clean the paper guide. If roll paper does not feed, cut the end straight across and uncurl it by rolling it backward, if necessary.
The Cause of Clogs

Printheads clog because nozzles get blocked by either air or ink. Clogs usually happen when: You keep printing with depleted ink cartridges. Using empty ink cartridges can result in air bubbles that can clog your cartridge and/or printhead.

If the quality of your printouts remains poor even after repeatedly cleaning and aligning the print head, one or some of the ink cartridges may be old or damaged and should be replaced. To replace an ink cartridge before the Status Monitor notifies you that the cartridge is empty, see Replacing an Ink Cartridge.
Paper is improperly loaded

If you have loaded the paper too far into the printer, the printer cannot feed the paper correctly. Turn the printer off and gently remove the paper. Then turn the printer on and reload the paper correctly.

Dust, paper fiber, and other debris might accumulate on the pick rollers and cause paper feed issues. To help prevent paper feed issues, clean the rollers inside the printer and in the duplexer (if equipped). If the other steps in this document fail to resolve the issue, then reset the printer.
If you have problems feeding paper, try these solutions: If paper does not feed for printing, remove it from the rear feed slot or cassette. Reload it, then adjust the edge guides. Make sure the paper stack is not above the tab on the edge guides inside the cassette or rear feed slot.
Ink cartridges that have been sitting idle in your machine for more than a couple weeks will eventually dry out. You might be able to bring them back to life by running a cleaning on your machine, but if the pattern continues, you will eventually be placing an order for a set of replacement cartridges.
Hey, you can reset Epson ink cartridge without resetter! As shown above, you can reset Epson chips by pressing and holding the button above the chip with a bent paper clip for 10 seconds.
The product prints a nozzle check pattern. Check the printed pattern to see if there are gaps in the lines. If there are no gaps, the print head is clean and you can continue printing. If there are gaps or the pattern is faint, clean the print head.
Using both hands, put one piece of paper in the manual feed slot until the front edge of the paper touches the paper feed roller. Once the machine has grasped the paper, let go. The side to be printed should be faced up. The machine will hold the paper in place until the print data is sent to the machine.
There are different methods of paper feeding. With dot matrix printers, paper is often feed through pins on a wheel that grab and slowly move paper through the printer. With inkjet and other page printers, paper is fed through the printer with rollers that grab and move the paper through the printer.
Select > Paper Setting > paper source > Print Adjustments > Paper Feed Adjust. Select one of the following: Auto: automatically adjusts the paper feed setting (takes 9 to 35 minutes to complete); Epson recommends running this option first.
Do a hard reset on your printer. To do this you just need to turn off your printer, unplug for a few minutes and then plug the printer again. If that still doesn`t work, try turning the printer and your computer off, and then start it back up again. Try uninstalling and then reinstalling your printer driver.
This error message is usually the result of a cartridge that is not firmly seated in its designated slot. To troubleshoot the problem, begin by completely removing the cartridge from its port. Reinstall the cartridge by positioning it so that it snaps into place and is securely fastened in its slot.
The printer will not operate if a black ink cartridge is expended or any cartridge is removed. If a color cartridge is expended, you may be able to continue printing temporarily with black ink. It`s best to always have extra cartridges on hand.
Head cleaning, ink charging, or ink drying is in progress

Check to see if the Pause light is flashing. If so, the printer is in the process of head cleaning, ink charging, or ink drying.

Method 1 – Bypassng Ink Cartridge on Epson Printer

After opening the lid, hold the ink button down. When you find the ink holer is moving to its position, then open the cartridge`s lid which is having no ink. Close it again without removing the cartridge. Close the lid and start to print.

The chip resetter tool is a self-contained unit that contacts the cartridge chip to get it to its electronic full setting, telling the printer it is full of ink and ready to print. It is generally used when re-inking a cartridge, because the cartridges must be removed from the printer to complete the process.
A cartridge reset tool is a plastic device with pins that, when inserted into the pinholes on your cartridge, reset the chip inside. The pins on the reset tool must line up with your cartridge`s holes, which are on the bottom or side edge.
The sponge end of a blocked printer head can be cleaned with only one liquid other than water. This liquid is isopropyl alcohol. Isopropyl alcohol isn`t strong enough to melt the sponge but is still strong enough to dissolve the ink inside the blocked printer head.
Your printer displays the “Missing or Failed Printhead” error to signal a malfunctioning printhead. The issue could be due to clogged ink nozzles, dirty ink cartridges, internal paper jams, and more. HP printers may also display this error if the printhead pulls air from ink cartridges.
A print head scratch occurs when an accumulation of dust or debris gets stuck in your machine. And if this happens, the damage cannot be fixed. In most cases, you would need to purchase a new printhead. That`s why it`s important to keep the dust out, away from your machine.
Make sure that the printer is turned on and the ink out light is off. Access the Print or Page Setup dialog box and click the Utility icon button, then click the Head Cleaning button. Follow the on-screen instructions. The power light and the ink lights flash while the printer performs the cleaning cycle.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Epson 7880 ink pump sucking ink
ANSWER : Not ink pump, but air pump, to put the ink feed under pressure.

Read Full Q/A … :

Epson EPL 7000

I bought a used Stylus Pro 3880 that needs some service or repair.
ANSWER : You’ll want to search online for the service manual for that unit, it will list the service req codes, and give you a quick expl

Read Full Q/A … :

Epson EPL 7000

stylus pro 9000 Printing garbage ( letters and characters)
ANSWER : OK I think the Main Board has gone bad. Does anyone know how difficult it is to replace it? Is it just an R&R situation? or is there more to it?

Read Full Q/A … :

Epson EPL 7000

Epson Stylus Pro 9800 Service / Repair Materials
ANSWER : service call error 00010005 . how to solve?

Read Full Q/A … :

Epson EPL 7000

Epson Stylus Photo T60 paper jam
ANSWER : paper jam

Read Full Q/A … :

Epson EPL 7000

Epson Stylus Photo R230 – flashing red lights fix
ANSWER : REDLIGHT

Read Full Q/A … :

Epson EPL 7000

Epson Stylus Photo R230(2 red indicator blinking)
ANSWER : 2 red indicator blinking

Read Full Q/A … :

Epson EPL 7000

run with empty ink cartridge
ANSWER : The only way is to buy a chip resetter and reset the chip on the cartridge. You can find them online for about $5. You just hold it against the cartridge until the light turns green. You do run the risk of damaging the printhead due to overheating because of no ink in it.

Read Full Q/A … :

Epson EPL 7000