HP LaserJet 4300
How to Identify and Fix Common Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
Recommended action. Turn the printer off, wait 15 seconds and turn the printer back on (using the power switch located on the back of the printer). The error code should not appear again.
If your printer`s status displays “Printer in error state,” there may be a problem with the printer itself. Make sure the printer is turned on and connected to your PC by Wi-Fi or cable. Check it for low paper or ink, and be sure the cover isn`t open and the paper isn`t jammed.
An E0 error indicates an unusable cartridge. This condition occurs when at least one ink cartridge needs attention, is faulty, incorrect, missing, damaged, or incompatible. Reseat both ink cartridges, clean the ink cartridge contacts, restart the printer, and replace one or both ink cartridges if necessary.
The 24 character error code is a failure of the short Disk Self Test ( DST ) and would indicate that the Hard Drive is failing and needs to be replaced. Hi, It means the hard drive has failed the quick test and needs to be replaced.
A new page should print with a claim code. If the page does not print, see the email address on the printer display. The first part of the HP ePrint address preceding “@hpeprint.com” is the claim code. For example, if your HP ePrint email is “firstname.lastname@example.org”, then “abc” is your claim code.
Make sure your devices are properly connected with each other, and the network or the cable you use to connect these devices is normal. You can also try restarting your HP printer. Turn it off completely and unplug the power cord, leave it for a couple of minutes, and then plug the cord back and power on the printer.
Error message “0x0000052e” indicates the following error: “Logon failure: unknown user name or bad password.”
To fix the error code 0x0000011b related to networked or shared printers, Microsoft says you should disable the print spooler privacy settings on both the Client PC (from which you work) and Print Server (Workstation to which the printer is attached).
Possible causes for this error include: Swing arms are not engaged. Lift motor or clutch failure. Dirty or defective encoder disk/sensor.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Error Code 51.1 says Printer Error No Kidding.lol
ANSWER : Sometimes turning off and on will allow you to print a few pages. The error is a beam detect error. The only real fix is to replace the laser scanner unit. Could be a loose connector on the scanner or DC controller from the scanner. That’s unlikely. You could try the only other free fix which is to open the scanner assy. and clean all the mirrors inside. The dust could obstruct the laser beam enough to cause the detect error.
Epson rx510 Printer Error solution
ANSWER : Hi all. I had similar problems as all of you with my RX510 I just bought it yesterday second hand. This info may help or encourage some one else. . .
Error Code 52.1M
ANSWER : Magenta laser error. The spinning motor bearings cause the squeal and that slows it down causing the error. You could try opening it and lubricating the motor shift with a drop of synthetic lubricant. Do not use more than a drop.
HP CLJ CP 5225 ERROR 55.0601
ANSWER : my printer cp5225 is giving me error code 55.0601 message which i can’t fix please help
Error Message 4F on MFC 210C
ANSWER : Basically this kind of error caused by loss of voltage on print head. If this is the case then I suggest to buy a new printer rather than replace print head. Print head might be too costly.
HP 9040 MFP Error code
ANSWER : bonsoir
Scanner error keeps coming up
ANSWER : I am having the same problem with my Epson Workforce 645
Density Shutter Error
ANSWER : I’ve never worked on one of those printers, but I have never, ever seen 1 valid solution for printer repair on fixya.com I read the replies there when I need a good laugh. Makes me wonder what the “techs” on that forum actually do for a living. It certainly couldn’t be printer repair.