HP Fax 750
Experienced technical support provide their insights in answering this question :
I am having the same problem with my Epson Workforce 645
How to Identify and Fix Common Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
A Scanner Error 22 error message displays on the printer control panel when you try to scan from the printer. This error might display when extra weight or pressure is applied to the scanner glass, such as when scanning an open book. The weight or pressure can stall the scanner mechanism.
The 52 Scanner error indicates that the printer has experienced an internal hardware error. Turn the product power off, wait at least 30 seconds, and then turn the product power on and wait for it to initialize. If you are using a surge protector, remove it. Plug the product directly into the wall socket.
The error displays for scanner hardware or power issues, such as a scanner bar jam or calibration issue, low scanner bulb temperature, or an internal or external electrical problem.
Run CHKDSK from Command Prompt
Type cmd (or command prompt) in the search box in your taskbar. Right-click Command Prompt and select Run as Administrator. Type chkdsk and hit Enter. This command will make the CHKDSK utility scan for problems without making changes.
When a 30.03.22 error is displayed on the control panel, it indicates that there is an error calibrating the scanner. Turn the printer off, and then back on to clear the error. If the issue continues, contact HP technical support to perform more complex troubleshooting steps.
The error may occur when there is a communication issue between the formatter and the scanner. Turn the printer off and then back on to clear the error message.
If a Firewall on your computer is active, it may be rejecting the necessary network connection needed for the network scanning software to operate properly. Disable the Firewall on your computer and try the network scanning again. Temporarily change your firewall/security settings to allow network connection.
23 or 30.03. 45 Scanner Errors. The resolution for either error is to, if preferred to send a firmware update, then replace the flatbed scanner assembly. It has been found that it is in most cases the internal lamp that has failed, but is not available through HP as a replaceable part.
So I understand, the problem “Error 20” is caused by problems in the flat cable to the scanner reader. To solve … Just changing the flat cable, it is necessary to access the guts of it and on the side. This requires knowledge of how to disassemble the equipment and a new flat cable.
a 52 Scanner error indicates the laser/scanner which writes the image to the drum has malfunctioned. This is a hardware error and most times the actual laser/scanner assembly needs to be replaced.
This error is due to the scanner driver not being installed properly.
Verify your scanner is installed
If you want to see if your scanner is installed, make sure that your scanner is turned on and use the Open the Printers & scanners settings button, or follow these steps: Select Start > Settings > Devices > Printers & scanners. Under Printers & devices, look for your scanner.
Scan initialization issues are typically caused by credential problems or connectivity issues to the remote scanner. Scanners that fail to initialize display detailed error messages in the hover text of a scheduled scan with a status of failed.
When a 30.03. 30 error appears on the control panel, it indicates that there is an issue with the scanner. Turn off the printer. Turn the printer back on, and verify that the scanner moves.
Normally a 30.01 error is a paper jam in the document feeder. Id check the ADF sensors and look for anything that could be causing a false alarm by the printer. and here: /t5/Multifunction-and-All-in-One/HP-CLJ-CM4730-MFP-30-01-34-scanner-failure/td-p/5963917#.
25 is a scanner assembly error. There is no need to update anything here but the scanner assembly itself. Check all of the contacts that the scanner assembly has to the main printer. Reseat them all to be safe and make sure they are nice and secure.
If it is only the 30.1. 13, this means there is a scan ASIC (application specific Integrated Circuit) hardware error. The ASIC resides on the Scanner control board. Typically a technician is disbatched with that type of service.
Occurs when the temperature of the diode sensor in the BJ cartridge head exceeds the prescribed level. Occurs when the diode sensor in the BJ cartridge head is assessed as irregular. The head temperature error always occurs before this error occurs.)
This means the baud rate is 9600 7 E for both the scanner and scale. If one tries to configure this Dual Cable device to a Single Cable device via bar codes it will beep once, reading the bar code, then emit a razz tone and throw an Error 13.
As per this document, Scanner Error 17 indicates that the scanner motor is in the incorrect position.
On resetting a scanner, it discards all of its explicit state information which may have been changed by invocations of useDelimiter(java.
Method 1: Update your HP scanner driver using Device Manager
2) Type “devmgmt. msc“, then press Enter on your keyboard. 3) Double click Imaging devices. Right click you scanner, then click Update driver.
A missing or outdated scanner driver can cause your HP scanner not to work, so you should update your scanner driver up to date. There are two ways to update your scanner driver: manually and automatically.
Cleaning your scanner
Unplug the scanner. Spray a specialist glass cleaner onto a soft, lint-free cloth or open a pre-moistened wipe. Raise or remove the lid of the scanner. Wipe the upper and lower glass plates until visible dust specks and grease have been removed.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Scanner error keeps coming up
ANSWER : I am having the same problem with my Epson Workforce 645
Read Full Q/A … :
HP Fax 750
Epson 630 close the scanner unit error
ANSWER : how to fix may epson printer
Read Full Q/A … :
HP Fax 750
52.0 SCANNER ERROR
ANSWER : Laser scanner assembly.
Read Full Q/A … :
HP Fax 750
Error Code 51.1 says Printer Error No Kidding.lol
ANSWER : Sometimes turning off and on will allow you to print a few pages. The error is a beam detect error. The only real fix is to replace the laser scanner unit. Could be a loose connector on the scanner or DC controller from the scanner. That’s unlikely. You could try the only other free fix which is to open the scanner assy. and clean all the mirrors inside. The dust could obstruct the laser beam enough to cause the detect error.
Read Full Q/A … :
HP Fax 750
My encolder has come off and i Cant get the screws to come out to open up
ANSWER : torx driver for an hp if thats what you have
Read Full Q/A … :
HP Fax 750
HP P1007 Printer Engine Scanner Error
ANSWER : My hp laserjet p1007 printer shows a massage that engine communication error
Read Full Q/A … :
HP Fax 750
Please help! Replace toner message keeps coming up! Brother DCM-1510
ANSWER : It’s a laser printer, there is no ink. You are going about it the wrong way. Watch this video. You can just skip the first part and go to 1:30 into the video. http://www.dailymotion.com/video/x1yakq1_how-to-refill-and-reset-brother-hl-1110-hl-1112-hl-1112a-dcp-1510-dcp-1512e-mfc-1810_tech
Read Full Q/A … :
HP Fax 750
scanner failure
ANSWER : That is a pretty old machine. You won’t be able to get any parts for it. Time to get a new one.
Read Full Q/A … :
HP Fax 750