Samsung clx-3305 transfer belt changed, and still problems

Samsung CLX 3305
I replaced the treansfer belt with a new one, and the printer still asks me to replace it? why? it prints, but print quality is not great and it keeps noise when warming up? i think that i replaced it right. and also new message asks me to replace fuser?

Experienced technical support provide their insights in answering this question :

You will need to enter Technician Mode on the printer.

How to Identify and Fix Common printer Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Upon installation of a new transfer belt an error message asking you to “Replace Transfer Belt” still shows. This error is caused by a counter inside your printer not being correctly reset when the new belt is installed. To fix this problem follow the steps below: Press MENU then #1934.

When a imaging unit has reached the end of life, the machine will stop printing. To prevent damage to the toner cartridge, do not expose it to light for more than a few minutes. Cover it with a piece of paper, if necessary.

Flail chest or chest trauma that includes multiple rib fractures that separate ribs from the skeletal wall are contraindications to gait belt use. These painful conditions would make proper tightening of the gait belt intolerable.

Dirt on the transfer belt can cause vertical black or color-streaks and lines to appear on prints. To remove black or color-streaks and lines on prints, use the Belt Cleaning Mode procedure.

Transfer belts have the following disadvantages: Belts that are too wide may affect a patient`s ability to lean forward. Narrow, unpadded belts may dig into the patient`s waist. Using a belt to lift all or most of a patient`s body weight is not an acceptable practice.

Among the more common technical issues that may bring down a printer are disconnected cables, malfunctioning routers, and low ink levels. Moreover, software problems such as interrupted connections or incorrect settings in your system`s drivers can also cause your printer to show up as offline.

Rotating the roller by turning the deep side of the drive axis clockwise (1), wipe the roller in the direction of the arrow from the front to the back. Clean the roller until there is no visible dirt or dust on the entire circumference of the paper transfer roller. Visually check that there is no dirt or dust.

The Occupational Safety and Health Administration (OSHA) recommends several best practices for using a gait belt. In all cases, make sure the belt is snug but not overly tight — two fingers should fit between the belt and your patient — and securely fastened so that the resident won`t undo it while being moved.

If the belt is too loose or slips this could force the engine to stall or shut down. This could be very dangerous if the car is on a busy road or motorway. i The car battery is dead. If the issue is severe, the battery will not be able to maintain its charge and could die shortly after the car has been started.

A transfer belt is essential for reducing the risk of injury during patient transfers. Transfer belts help provide support and balance to patients, so caregivers face significantly less risk of injury while transferring individuals from one room or device to another.

which of the following is true of transfer belts? they fit around the residents waist over his clothes. side boards are used for: transferring residents who cannot bear weight on their legs from one sitting position to another.

This month I have started the process of “resetting” each room in my house, once per week. This is done by dedicating 1–2 hours to cleaning your entire space and refreshing it for the next week to come. It is a simple concept but ultimately makes any tidying throughout the week easier.

These gait belts are made of cotton webbing with a metal buckle to help aid caregivers when lifting or transferring mobility patients. They also come in a variety of lengths and colors and can be adjusted quickly and easily.

Immerse your belt

Use a soft cloth or washer to gently rub the dirt and grime away. Do this gently. The soap will do most of the actual work, and you don`t want to scour the leather. Just rub in small circular motions to dislodge any stubborn dirt.

Daily Cleaning and Maintenance

It`s important to do standard maintenance on your leather belt every time you wear it. The process removes any contaminant or impurity that might damage the surface of your belt before it can settle into the material.

Depending on the model, a typical life span on an office copier can range from three to five years. The life span of your copier largely depends on the copy volume and maintenance. Most copier models are designed to produce 1,000 copies per month at the low end, with higher-end copiers producing upwards of 50,000.

If your printer`s status displays “Printer in error state,” there may be a problem with the printer itself. Make sure the printer is turned on and connected to your PC by Wi-Fi or cable. Check it for low paper or ink, and be sure the cover isn`t open and the paper isn`t jammed.

Reset. Resetting the printer stops printing and clears the current print job received from the active interface. You may want to reset the printer when there is a problem with the print job itself and the printer cannot print successfully.

Power down the printer and then unplug the power cord from the printer and the wall. Wait for a minute, then plug the printer back in. The printer will reset and turn on.

Poor print quality is the most common complaint people have about inkjet printers. These problems often show up in the form of horizontal white lines running through each line of print. If you run into these types of issues, you can sometimes fix them by cleaning the print head.

Common causes include dust and grime, worn rollers, or inappropriately weighted paper. Prevent paper jams by regularly cleaning your printer and replacing parts as needed. Check the weight of paper that your printer is rated for as well. The printed product is faded.

The drum unit may need replacing if you notice the printer producing blurry, low-quality images. Black or colored toner spots on printouts also indicates a failing drum unit. In some cases, horizontal lines may develop across the printout every time the paper passes the failing part of the drum.

Replace the transfer roller when the percentage of remaining life is less than 20 percent.

Cleaning other rollers

Do not clean the transfer roller; alcohol and pressing on the roller can damage the roller and cause print-quality problems.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Samsung clx-3305 transfer belt changed, and still problems

ANSWER : You will need to enter Technician Mode on the printer.

Read Full Q/A … :

Samsung CLX 3305

Samsung ML 1640

ANSWER : My Samsung ML1640 Monochrome Laser Printer showing ” no power” The red light is instantly going off. What should be the reason? The printer is rarely used. (may be once in a month).?

Read Full Q/A … :

Samsung CLX 3305

Samsung ML-1610 toner low warning need reset help!

ANSWER : in my printer shows the online error problem

Read Full Q/A … :

Samsung CLX 3305

Samsung ML 2165 Error lights

ANSWER : Hi there, I am having the same problem. Stupidly I bought a second replacement (genuine Samsung) cartridge thinking it may have been a faulty cartridge as sometimes it deemed to work after a bit of messing around. SO NOW I HAVE ONE NEARLY NEW AND ONE COMPLETELY NEW ; ABSOLUTELY NO USE TO ME – unless I can get the printer to accept them.

Read Full Q/A … :

Samsung CLX 3305

I want to resat page count my printer samsung ml 1640

ANSWER : my printer toner was exhausted Samsung ML1640

Read Full Q/A … :

Samsung CLX 3305

how to reset samsung scx 4521f

ANSWER : my samsung SCX 4521X printer and photostat shows LSU error and not functioning . please find solution.

Read Full Q/A … :

Samsung CLX 3305

Samsung-chip-ML-1865W-V3.00.01.10-CRUM-reset Fix Firmware

ANSWER : no