Unknown Printer

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Hold down the red stop/clear button on the printer and then the same time hold down the start button, wait approx 1 min.
Upon installation of a new transfer belt an error message asking you to “Replace Transfer Belt” still shows. This error is caused by a counter inside your printer not being correctly reset when the new belt is installed. To fix this problem follow the steps below: Press MENU then #1934.
RESET THE PRINTER

Switch the printer on and unplug the cable completely, both the USB connection on the device and the plug to the power socket. Wait for at least a minute. c. Reconnect the cable and plug it to the power source.

The transfer unit is the part of the laser printing process that is responsible for transferring the image on the page before it goes through the fusing unit. Transfer units do eventually wear out and need to be replaced after an extended period of use.
Restoring the factory-set defaults returns most of the settings to the factory defaults. It will not reset the page count, tray size, or language.
To change your printer IP address, type its current IP address into the address bar of a web browser. Then go to the Settings or Network page and change your printer`s network to a static/manual IP address. Finally, type in the new IP address.
Resetting the NVRAM will reset all printer values including network, printer setup, job defaults, margin and paper calibrations to factory defaults. Note: It is recommended to print a configuration page prior to resetting the NVRAM. Press the Down Arrow and scroll to Troubleshooting.
a misprint or misspelling in a text.
The default User ID is admin and Password is sec00000, but it can be changed from the default.
Reset. Resetting the printer stops printing and clears the current print job received from the active interface. You may want to reset the printer when there is a problem with the print job itself and the printer cannot print successfully.
Reset. Resetting the printer stops printing and clears the current print job received from the active interface. You may want to reset the printer when there is a problem with the print job itself and the printer cannot print successfully.
The connection cable between the computer and the machine is not connected properly. Disconnect the machine cable and reconnect it (see Rear view). The connection cable between the computer and the machine is defective. If possible, attach the cable to another computer that is working properly and print a job.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Samsung clx-3305 transfer belt changed, and still problems
ANSWER : You will need to enter Technician Mode on the printer.

Read Full Q/A … :
Unknown Printer

oki c511 drum reset, toner reset, turkey chip reset
ANSWER : If you switch off toner control, you should keep an eye on your prints, and we aware of ink quality, so filling colours as they’re emptying. Nevertheless, it’s an small disturb for the a,ount of money you’re saving ¿isn’t it?

Read Full Q/A … :
Unknown Printer

Samsung-chip-ML-1865W-V3.00.01.10-CRUM-reset Fix Firmware
ANSWER : no

Read Full Q/A … :
Unknown Printer

how to reset samsung scx 4521f
ANSWER : my samsung SCX 4521X printer and photostat shows LSU error and not functioning . please find solution.

Read Full Q/A … :
Unknown Printer

Samsung ML-1610 toner low warning need reset help!
ANSWER : in my printer shows the online error problem

Read Full Q/A … :
Unknown Printer

Transfer belt doesn't reset the counter HP 4700
ANSWER : It is not possible to reset the counter of HP CLJ 4700. for further please check http://www.tinylinks.co/xyjX

Read Full Q/A … :
Unknown Printer

ip4200 INK TANK RESET and WASTE TANK RESET
ANSWER : Different cartridges, notwithstanding, don’t have a ‘fill gap’ so you’ll have to make one yourself. Our refill units for these sorts of cartridges accompany a smolder apparatus which is utilized to blaze (really dissolve) a fill opening in the cartridge . Our refill guidelines will demonstrate you precisely where to make the fill opening (you would prefer not to make it in the wrong spot). A blaze device come standard in all refill packs for cartridges without processing plant made fill openings. if you want to get proper detailed information then call us at 1-888-924-2961for more information regarding canon printer support.

Read Full Q/A … :
Unknown Printer

Reset HP Color Laserjet 4700 transfer kit
ANSWER : How about the situation when resistor does not reset the transfer belt count and even new transfer belt out of the box is not doing it. Do you have any idea how to solve this problem? I did reset transfer belts and fusing units on several HL 4700 printers with no problem but also I came across few which were not possible to reset even with oryginal parts.

Read Full Q/A … :
Unknown Printer