Unknown Printer

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

If your drum is not recognizing in the printer, there may be an issue with the gold chip on the end of the toner cartridge. This chip communicates with the printer to create a print and if it is not reading properly, the toner / drum unit will not work. Sometimes fingerprint oil or dust can cause this error.
A degraded drum unit can cause streaks, smudges, and blank spots on your printed page even if you just inserted a new printer toner. While a broken drum unit won`t break your printer, it will just fail to stop printing at a certain point.
The Brother machine will display a `Replace Drum` or `Drum Stop` message when the machine has printed approximately 15,000 pages. The drums should be replaced as a set in order to maintain print quality. Unlike the toner cartridges, the drum change is not automatically detected by the machine when they are replaced.
The biggest tell is misprinted pages. If you have a new Brother toner, and the printer still puts out pages with obvious streaking on them – it`s time for a drum unit replacement. Don`t let bad printouts make you seem unprofessional – replace or fix your Brother printer drum today!
Drum Error typically appears when the corona wire on the drum unit needs to be cleaned or when the drum unit needs to be replaced. If you replaced the drum and the message appeared or continued to appear immediately after installing the replacement drum, click here. 1. Clean the corona wire inside the drum unit.
Printer drum repair is an important service that requires knowledge and experience to complete in order to restore your printer. It includes troubleshooting printer drum problems such as HP, Brother and others, cleaning printer drum cartridges, replacing printer drum 88a and buying printer drum cleaning.
Use an activated toner cloth, stretched tautly, and carefully wipe down the drum exterior to remove loose toner. Then use a cotton ball saturated with 99% pure isopropyl (rubbing) alcohol. Clean any patches of stubborn toner still attached to the drum. Use toner cloth or lint-free microfiber to clean the print rollers.
There are many factors that determine the actual drum life, such as the temperature, humidity, type of paper, type of toner used, number of pages per print job and so on. Under ideal conditions, the average drum life is estimated at approximately 12,000 pages.
“Replace Drum” continues to appear on the display after the drum has been replaced. If your machine continues to display “Replace Drum” after installing a new drum, the drum counter may not have reset properly. Whenever you replace the drum unit, the drum counter needs to be reset.
Drum heads wear out!

Drummers who practice a lot should probably change heads once every six months. Drummers who own their own drums can probably change the heads without any problem, but if it is the first time, it might be a good idea to have someone at the drum shop, or an experienced drummer, teach you.

The good news is brake drums are built to last 100K to 150K miles and are easy to maintain. However, the parts inside the drum need to be inspected and serviced more frequently.
Use the drum unit until you have a print quality problem, then replace the drum unit with a new one. The yield of a drum unit is approx. 15,000 pages (1 page/job). There are many factors that determine the actual drum life, such as the temperature, humidity, type of paper, type of toner used and so on.
OPC (organic photoconductor) drum is a critical component of printer or copier that impacts the image printing performance. Characteristics. Applications.
For natural skin drum heads, like those on a djembe drum or bongos, small cracks and tears can be filled in with glue, while larger holes could be patched with extra skin. However, both of these methods could change the sound of the drum, and completely replacing the natural skin drum head may have better results.
Why do I need a drum? Without a drum unit, the toner powder in the cartridge cannot be transferred onto the page. The two parts work together to create a print! You can`t have one without the other and expect the printer to work properly.
If your machine continues to display “Replace Drum” after installing a new drum, the drum counter may not have reset properly. Whenever you replace the drum unit, the drum counter needs to be reset.
The Drum LED blinks if the drum unit is near the end of its life. Use the drum unit until you have a print quality problem, then replace the drum unit with a new one.
If your machine continues to display “Replace Drum” after installing a new drum, the drum counter may not have reset properly. Whenever you replace the drum unit, the drum counter needs to be reset.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Samsung CLP-365W Blinking Error
ANSWER : Hi, I’ve fixed the same error installing the fw CLP365W_v3.00.02.16.exe

Read Full Q/A … :
Unknown Printer

Samsung clx-3305 transfer belt changed, and still problems
ANSWER : You will need to enter Technician Mode on the printer.

Read Full Q/A … :
Unknown Printer

Samsung CLP-300 Image Ghosting
ANSWER : Hi there – did you resolve your issue? It exactly mirrors the issue with my Samsung CLP-310. Each print carries across to the subsequent print as a ghost/smeared image and I diagnosis has revealed the transfer belt (ITB) has smeared toner remaining post each print. I was therefore considering replacing the Transfer Belt, but fear it is not the issue as you found. Whatever should be removing the toner from the Transfer Belt post print, is not, and then I get smeared ghosting on subsequent prints of the last print. The only mitigation is to print 5 blank pages post print, then the ghosting/smearing reduces to nearly zero (proving that the toner is being removed partially at least)…. Any help gratefully received.

Read Full Q/A … :
Unknown Printer

replace with new imaging unit error
ANSWER : samsung clp 365w firmware

Read Full Q/A … :
Unknown Printer

Samsung ML-1610 toner low warning need reset help!
ANSWER : in my printer shows the online error problem

Read Full Q/A … :
Unknown Printer

REMOVE FUSER UNIT
ANSWER : It looks real easy. https://www.youtube.com/watch?v=fbilywC620A

Read Full Q/A … :
Unknown Printer

Chatter from toner cartridges before printing
ANSWER : The video may have the answer you want

Read Full Q/A … :
Unknown Printer

Clean Printing
ANSWER : Simply look at the drum and the belt. If there is still a latent image on either one, that is what you should replace.

Read Full Q/A … :
Unknown Printer