Samsung CLP 365W
Experienced technical support provide their insights in answering this question :
Hi, I’ve fixed the same error installing the fw CLP365W_v3.00.02.16.exe
How to Identify and Fix Common Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
Hold down the red stop/clear button on the printer and then the same time hold down the start button, wait approx 1 min.
If a corresponding LED is solid red, along with a blinking red status light, check the following: A small amount of toner might remain in the toner cartridge. A minor error might have occurred.
Orange. Blinking. Upgrading firmware. On. A paper jam has occurred (see Clearing paper jams).
The Power light blinks at a steady interval when the printer is processing a print job. If the Power light blinks fast, the ink cartridge door might be open, or the printer might be in an error state. If an error message displays on the computer screen, follow the on-screen messages to resolve the issue.
A flashing red light usually indicates a power supply problem. The simplest solution is often to plug your TV into a different power source. Unplug your Samsung TV and wait 30 seconds, then try plugging it into a different outlet that you know is working.
Ink may have run out (The lamp on the ink tank flashes). If printing is in progress, you are recommended to stop printing, replace the ink tank, and then print again.
Meaning: the paper exit tray is closed / Paper jam. Solution: the paper is jammed. Remove the jammed paper, replace the paper correctly in the printer, and then press the Resume / Cancel button.
Printer detected ink out condition (The lamp on the ink tank flashes). Stop printing, replace the ink tank, and then print again. Be sure to replace the empty ink tank before resuming printing.
The printer drops the network connection, resets its network settings to their factory defaults, and prints a Printer Configuration label and a Network Configuration label.
Reset. Resetting the printer stops printing and clears the current print job received from the active interface. You may want to reset the printer when there is a problem with the print job itself and the printer cannot print successfully.
Power down the printer and then unplug the power cord from the printer and the wall. Wait for a minute, then plug the printer back in. The printer will reset and turn on.
The default User ID is admin and Password is sec00000, but it can be changed from the default. note: The password might not be sec00000 if an admin has set the password to something different, or if the printer is an older model (for older models, the default password is 1111).
The machine may be configured incorrectly. Check the Printing Preferences to ensure that all of the print settings are correct. The printer driver may be incorrectly installed. Uninstall and reinstall the machine`s driver.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Samsung CLP-365W Blinking Error
ANSWER : Hi, I’ve fixed the same error installing the fw CLP365W_v3.00.02.16.exe
Samsung ML 2165 Error lights
ANSWER : Hi there, I am having the same problem. Stupidly I bought a second replacement (genuine Samsung) cartridge thinking it may have been a faulty cartridge as sometimes it deemed to work after a bit of messing around. SO NOW I HAVE ONE NEARLY NEW AND ONE COMPLETELY NEW ; ABSOLUTELY NO USE TO ME – unless I can get the printer to accept them.
Samsung-chip-ML-1865W-V3.00.01.10-CRUM-reset Fix Firmware
ANSWER : no
Samsung SCX -4300 error
ANSWER : My printer show toner exhasted replace toner
replace with new imaging unit error
ANSWER : samsung clp 365w firmware
Samsung ML-1610 toner low warning need reset help!
ANSWER : in my printer shows the online error problem
Error Code 51.1 says Printer Error No Kidding.lol
ANSWER : Sometimes turning off and on will allow you to print a few pages. The error is a beam detect error. The only real fix is to replace the laser scanner unit. Could be a loose connector on the scanner or DC controller from the scanner. That’s unlikely. You could try the only other free fix which is to open the scanner assy. and clean all the mirrors inside. The dust could obstruct the laser beam enough to cause the detect error.
I want to resat page count my printer samsung ml 1640
ANSWER : my printer toner was exhausted Samsung ML1640