Samsung CLP 300N
How to Identify and Fix Common Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
The most common cause of paper jams is the paper; please check the user manual to make sure the media being used is recommended for the printer. Also, make sure the printer and driver setting match the paper type. When the printer displays Jam 2, the paper has failed to pass through the paper exit area.
If the paper is jammed inside the printer, use the handle to completely open the access door. Grasp the handle of the toner cartridge, and then gently remove the cartridge. Remove any visible jammed paper from inside the printer. Reinsert the toner cartridge back into the printer.
Paper Does Not Feed into Printer
Paper might not be loaded correctly. Remove the paper and make sure the paper is aligned with the tray. Check that the guides are aligned correctly. There is too much paper in the tray.
Low Quality and Improper Storage of Ink and Toner Cartridges. Low-quality cartridges or improperly stored cartridges can cause paper jams. For example, too much toner or ink can be released onto the paper, or the toner or ink can clump together in the cartridge.
Low-quality paper leaves an accumulation of tiny paper bits often referred to as “paper dust” inside the machine. This “dust” is one of the top causes of paper jams. More dust means more jams. Besides jams, the dust also contributes to poor-quality prints and causes machine parts to wear at a faster rate.
It`s important to replace the drum promptly when it`s low to avoid any further damage to the printer and to maintain optimal print quality. A bad drum may cause paper jams because it can cause the toner to be unevenly distributed on the paper, leading to jams or misfeeds.
Check that the correct paper is properly loaded into the printer and is not jammed. Replacing damaged cables, plugging in loose or disconnected cables, and fixing paper jams as necessary may resolve the issue.
– If the grinding or clicking noise occurs, the toner cartridge is the cause. You will need to replace the toner cartridge (TN630 or TN660) to resolve this issue.
– If the grinding or clicking noise occurs, the toner cartridge is the cause. You will need to replace the toner cartridge (TN630 or TN660) to resolve this issue.
Paper curl is caused by an excess amount of moisture in the paper. The first step to ensure less paper curl is to store your paper in a cool, dry area. By doing so, you will reduce the amount of moisture and humidity the paper is exposed to. The next step is to always fan the paper before placing in the machine.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.
ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.
Read Full Q/A … :
Samsung CLP 300N
hp 8600 pro when power on, paper jam message appear but there is no paper jam in the tray
ANSWER : Hp 8180 Photosmart All In One code keeps says paper jam and carriage jam when neither are jammed. I followed all the recommended things to do. I live in Raleigh NC any place to take this or any suggestion.
Read Full Q/A … :
Samsung CLP 300N
Paper Jam and carriage jam code when nothing is jammed
ANSWER : Did you try cleaning the encoder strip that runs through the cartridge assy.? Use Window Cleaner on a paper towel. Also, check inside on the right. I’ve seen a lot of times where there is a folded up scrap of paper that stops the carriage from going all the way to the right.
Read Full Q/A … :
Samsung CLP 300N
Paper jam in tray 2 (but no paper pulled from tray) also M476DN models
ANSWER : Isopropyl alcohol is not recommended for rubber rollers. It dries out the rubber and hasten it’s cracking and breaking. It will do nothing to restore the grip. Those rollers are really hard to replace. It would be easy if that dumbass secondary menu really worked. None of the techs I’ve spoke to ever got into it. Everyone I know sends a print job and listens for the roller to rotate into position where you can pull it off.
Read Full Q/A … :
Samsung CLP 300N
Paper Jam error but no paper jam
ANSWER : Obviously you didn’t get all the paper cleared out. There is a small scrap in the paper path causing the jam when the paper hits it. You can try clearing it out by inserting something stiff like a piece of file folder from the back of the printer into the paper path and pushing the offending piece out that way.
Read Full Q/A … :
Samsung CLP 300N
Canon mx410 Paper jam message, but no paper jam?!
ANSWER : I have exactly the same problem, no answers 😳
Read Full Q/A … :
Samsung CLP 300N
Keep getting a paper jam message. There is no jam.
ANSWER : You can quit wondering. Parts are unavailable. I’ve seen posts where people have 3D printed the parts or machined them out of metal.
Read Full Q/A … :
Samsung CLP 300N
paper jam 2
ANSWER : That is a jam in the exit part of the printer.
Read Full Q/A … :
Samsung CLP 300N