HP DeskJet Deskjet
How to Identify and Fix Common Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
Power off the printer by holding the power button for 60 seconds straight. This will reset the memory of the cartridge in there and will consider it as a new one.
In the product software, double-click Printer Actions ( ). Double-click Maintenance Tasks ( ). The HP Toolbox opens. Click Clean Ink Cartridges, and then follow the on-screen instructions to clean the cartridges.
Just above the circuit board on most printer cartridges, you`ll find a small button. You`ve seen these tiny buttons before on cell phones, phone chargers, etc. This is your reset button, and the only way to get in there is either with a paper clip or the tip of a pen (which will leave a tiny ink smudge on the button).
One or both empty ink level icons blink, the Ink Alert light is on, and the Resume light and Error icon blink. This condition occurs when at least one ink cartridge is incompatible or the ink levels are low. Make sure your ink cartridges are compatible with your printer and there is adequate ink in the cartridges.
Turn the product on while you press and hold the Resume button for 10-20 seconds. The Attention light turns on. Release the Resume button. The Attention and Ready lights cycle while the product restores factory defaults.
Press the button on the chip-reset tool for several seconds until the LED light on the device goes off. Then, unlock the reset tool from the cartridge. Use the resetter with other cartridges and install them back into the corresponding slots in your printer. Voila!
There are chips inside the original cartridges to record how many pages were printed and they cannot be reset. As a result the printer reads the chips and tells you that the cartridges are empty, even though they are not. This is why you are getting the “ink low” message even though the ink tank is at full capacity.
If your printer is turned on, disconnect the power cord from the printer. Keep the power plug unplugged for 60 seconds, reconnect the power cord to the wall, and turn on the printer. If the error persists, remove the cartridge from the printer, clean the cartridge contacts with a cloth, and reinstall the cartridges.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Reseting the ink levels for hp c7280,
ANSWER : I held the # and 6 down long enough to start a complete re-set of the printer But the Black ink level still shows as depleted when it is actually still half full.
Resetting of chip for hp toner Q6000A
ANSWER : HP Color Laser Jet 1600 – Thanks for all the above information. Even though the 1600 is a different printer, I followed the above: “…go to “System Configuration”; then to “Print Quality”; I then get a choice of “Replace Supplies” and then “Overide Out”…” Selecting “Overide Out” got my 1600 back to printing, although I did have do perform the steps TWICE before it seemed to take affect. Not sure what was going on, but I’m happy that people put the information out there for the rest of us to have.
HP DeskJet 950C Leaking Ink
ANSWER : Thanks for the “loose, white rectangular piece” comment in my 990cse. I found this same white piece of rubber today jamming up the cleaning station carriage assembly and was wondering where it came from!
HP C6180 Hard Reset procedure
ANSWER : How do I hold down the # and the 6 at the same time? The “#” requires holding the shift key and the “6” doesn’t. Maybe you all have a different type of keyboard. My printer is HP 1220C.
oki c511 drum reset, toner reset, turkey chip reset
ANSWER : If you switch off toner control, you should keep an eye on your prints, and we aware of ink quality, so filling colours as they’re emptying. Nevertheless, it’s an small disturb for the a,ount of money you’re saving ¿isn’t it?
HP Color Laserjet 500 series M551n Error 98.00.0C
ANSWER : I just ran into one of these on a 4 year old m551. Failed to complete startup at the end of disk check. Followed the above link for troubleshooting.
HP laser jet 3015 "Upgrade Error Call HP Support"
ANSWER : rgtr
Hp 3110 ink system failure
ANSWER : Well I just solved my issue with my hp 3310 displaying the ink error code. I held the OK cancel black and color buttons down at same time. And while holding those down hit the power button when machine shut off I released buttons hit power button on it came on and shut off. Hit power button again and it will reset machine and run a maintainace program. When all is done run a print report. Mine works fine. Good luck.