Epson Stylus Photo R380

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

What should I do? The ink cartridges may not have been installed using the correct procedure or they may not be seated correctly. Follow the instructions below to correctly install and reseat the ink cartridges. Turn on your product.
Remove the cartridges from your printer – switch your printer off. Using a piece of damp kitchen roll, gently wipe the copper plate on the cartridge. Allow the chips to air dry. Once the chips are completely dry, re-install the cartridges into your printer and switch the printer back on.
Method 1 – Bypassng Ink Cartridge on Epson Printer

After opening the lid, hold the ink button down. When you find the ink holer is moving to its position, then open the cartridge`s lid which is having no ink. Close it again without removing the cartridge. Close the lid and start to print.

The message Replace Toner will not clear from the display if: – The replacement toner cartridge is not installed properly. – A starter toner cartridge is installed as a replacement toner cartridge. – A toner cartridge from another machine or a used toner cartridge is installed as a replacement toner cartridge.
Clean the Cartridge Contacts: one of the most common reasons you might get a cartridge problem error when your cartridges are new and full is the contacts on the cartridge might be dirty or otherwise obscured from making good contact with the electronics in the printer head carriage.
Press the left or right arrow button to select Maintenance > Reset Ink Level. Press the start button, the OK button twice, and then the start button again. Press the right or left arrow button to highlight the ink tank you refilled and press the OK button to select it. Repeat for each ink tank color you refilled.
There is a possibility that it didn`t properly click into the designated slot. If this is the case, you should lift the cover and double-check in order to verify that the cartridge is clicked into place. Otherwise, it would not be possible for the printer to detect it.
Verify the ink cartridge(s) is inserted properly. Some cartridges snap in place, and if they are not inserted fully, the printer won`t print anything. If a lever is moved from its original position to allow for installation of ink cartridges, ensure it is returned to its original position.
Your Epson printer may have failed to recognize the new ink cartridge, or its ink level system has read it as empty. For numerous Epson printer models, there`s a way to bypass this built-in ink checking system through a quick cartridge reset. Raise the printer`s top cover and then hold the Ink button.
The Cause of Clogs

Printheads clog because nozzles get blocked by either air or ink. Clogs usually happen when: You keep printing with depleted ink cartridges. Using empty ink cartridges can result in air bubbles that can clog your cartridge and/or printhead.

Hey, you can reset Epson ink cartridge without resetter! As shown above, you can reset Epson chips by pressing and holding the button above the chip with a bent paper clip for 10 seconds.
There are chips inside the original cartridges to record how many pages were printed and they cannot be reset. As a result the printer reads the chips and tells you that the cartridges are empty, even though they are not. This is why you are getting the “ink low” message even though the ink tank is at full capacity.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Error message "Cannot recognize the following cartridge(s). Install them correctly."
ANSWER : The cartridges all have chips on the bottoms. Only thing you can try is cleaning the chips and the contacts in the cartridge holder assy.

Read Full Q/A … :

Epson Stylus Photo R380

erro message (install genuine hp cartridge)
ANSWER : It seems like it might be a 4240 board. The 4240 was pretty much the same printer, but sold for $200 less. The downside is that it wouldn’t accept the 42X cartridges.

Read Full Q/A … :

Epson Stylus Photo R380

Expired Ink Cartridges – Any way to move paper with old cartridges?
ANSWER : You could try disconnecting the printer from the computer. Then change the date on the panel to prior to the expiration date. That should fool it.

Read Full Q/A … :

Epson Stylus Photo R380

new cartridges but message says one or all must be replaced
ANSWER : Make and Model would help!!

Read Full Q/A … :

Epson Stylus Photo R380

error message that says " remove shipping lock from black cartridge" even though it has been removed
ANSWER : http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c01760760

Read Full Q/A … :

Epson Stylus Photo R380

Error message reads remove and check right cartridge
ANSWER : You can try cleaning the contacts on the back of the cartridge and the ones that they contact in the printer. Other than that, you have to replace the cartridge. I once had one that did the same thing. I swapped the cartridge with another printer of the same model and both printers worked fine. I swapped them back and the original printer got the same error. The other printer had no problem with either cartridge. I swapped them back and left them that way.

Read Full Q/A … :

Epson Stylus Photo R380

Waste Toner Cartridge is empty but printer is still telling me to replace it
ANSWER : All of the ones I’ve seen are optical. Light shines through a transparent section of the waste box onto a photocell. If toner builds up past that area, it gives a warning to replace it. Possibly toner dust has gotten on the photocell.

Read Full Q/A … :

Epson Stylus Photo R380

Epson, sudden cannot recognise cartridges error
ANSWER : Hi, I have exactly the same problem than you, I’ve been trying to solve it since 6 months. I have an Artisan PX730 WD, and the genuine cartridge can’t be recognized all together. And status monitor indicates same thing than you.

Read Full Q/A … :

Epson Stylus Photo R380