Canon Pixma IP4700
Anyone advise how to get over this error? My nearest Canon Service Centre is 400 miles away!

Experienced technical support provide their insights in answering this question :
Resetting the waste ink absorber on a Canon printer can resolve some error codes that appear when turning it on.

How to Identify and Fix Common printer Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

The 5200 error would point to a problem with the print head in the MB2720 or a problem with the ink system. If you have tried turning the printer off and on and the inks are seated properly, it looks like the printer needs service.
This error is that your waste ink is full. Reset the printer. Press the reset button and hold it while it`s off. Then, turn it on and press the reset button twice.
The Canon 5200 error is often related to the ink levels present in printer cartridges. Turning your printer off and on again can reset the printer`s mechanism for reading ink levels and get you back to printing in no time.
The error 5200 is connected to ink levels and usage within your printer. Issues such as low ink levels, a defective ink cartridge or a dirty printhead can trigger this error.
Check the remaining ink level, and then refill the ink tanks if necessary. Turn off machine and unplug it. Plug in machine again and turn it back on. Perform print head Cleaning.
Vehicle Code ยง 5200 is the California statute that requires owners of motor vehicles to fasten and display license plates on their vehicles. Failure to do so is an infraction punishable by a $197.00 fine, plus court costs.
Turn off printer and unplug it. Plug in the printer again and turn it back on. If this does not solve the problem, service is required. For support and service options, sign into (or create) your Canon Account from the link below.
The 5207 error can be caused by a paper jam. Canon has 2 videos that you can view in regards to resolving paper jam or paper feed issues. Please view the following two troubleshooting videos available from the MAXIFY MB2320`s Support Page: 1.
If your printer`s status displays “Printer in error state,” there may be a problem with the printer itself. Make sure the printer is turned on and connected to your PC by Wi-Fi or cable. Check it for low paper or ink, and be sure the cover isn`t open and the paper isn`t jammed.
You can run a power ink flushing to replace all of the ink in the ink tubes if necessary. This may improve print quality, but consumes more ink than the head cleaning or powerful cleaning options. This process can take up to 20 minutes.
Solution. There are several reasons for Error 5100 to appear, including a paper jam, an improperly seated ink tank, and more. Encoder (Timing) Strip on the printer needs cleaning. Manual cleaning can be done on some models.
Issue. When the message “Ink absorber full.” is displayed, the printer stops printing and needs ink absorber replacement. Push the power button to turn OFF the printer, and then contact the service center for replacement. Request either Canon or the dealer you purchased the machine for a repair service.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Error Code 51.1 says Printer Error No Kidding.lol
ANSWER : Sometimes turning off and on will allow you to print a few pages. The error is a beam detect error. The only real fix is to replace the laser scanner unit. Could be a loose connector on the scanner or DC controller from the scanner. That’s unlikely. You could try the only other free fix which is to open the scanner assy. and clean all the mirrors inside. The dust could obstruct the laser beam enough to cause the detect error.

Read Full Q/A … :

Canon Pixma IP4700

PRINTER MX 320 CANON ALL IN ONE PRINTER
ANSWER : Probably a worn feed roller. You can try cleaning it with a damp rag as it might just be covered with paper dust.

Read Full Q/A … :

Canon Pixma IP4700

Difference Between Laser Printer and InkJet Printer
ANSWER : Laser uses toner which is a powder that gets melted onto the page. Inkjet uses ink that gets squirted onto the page.

Read Full Q/A … :

Canon Pixma IP4700

Printer error Oxc18a0201
ANSWER : Have no idea what model you have, but try this forum post or search through the site using your model and error.

Read Full Q/A … :

Canon Pixma IP4700

canon printer error
ANSWER : Here are the procedure to fix Canon smartbase MP730 printer error ##334

Read Full Q/A … :

Canon Pixma IP4700

Printer error 5200
ANSWER : Resetting the waste ink absorber on a Canon printer can resolve some error codes that appear when turning it on.

Read Full Q/A … :

Canon Pixma IP4700

printer error fix
ANSWER : Epson 2540

Read Full Q/A … :

Canon Pixma IP4700

newly installed printer…can scan but cant be set as a default printer???
ANSWER : ITS AN EPSON L210…

Read Full Q/A … :

Canon Pixma IP4700