Epson Stylus C88+
Is it possible to replace the print head sponges in the Epson C88+ printer? If it is where can I purchase them?

Experienced technical support provide their insights in answering this question :
Yes, but Epson won’t sell them to you. If you can figure out how to get to them, you can just take them out and wash them in hot water. Otherwise, Google how to reset the warning message on your model. The tanks hold much more ink than the warning permits.

How to Identify and Fix Common printer Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Essentially the printhead contains an ink chamber, with a piezo electric actuator, made of a material such as Lead Zirconium Titanium (PZT). When an external electrical charge is applied to PZT it changes shape, forcing a drop of ink from the ink chamber and out through the nozzle.
There are a number of porous pads in the printer that collect, distribute, and contain ink that is not used on printed pages. Ink is collected by these pads during the initial setup of the product, during cleaning cycles, and when printing borderless photographs.
The heating element (comprising of tiny resistors) rapidly heat a thin layer of liquid ink. The heated ink causes a bubble to form, expelling the ink through a nozzle. The heat also forces air out of the ink molecules. The ink is then fired out at a velocity of up to 20 metres per second.
What is a printhead? The answer is simpler than you may imagine. The printhead is a component in a printer that houses ink cartridges. It`s typically located under the cover of your printer, and it can become clogged with ink over time.
Although different brands of cleaning solution will slightly vary when it comes to ingredients and ingredient ratios, they are largely based on the same three components: Distilled water. Isopropyl alcohol. Detergent.
Cleaning pen is suitable for use with Inscripta thermal CD printer. Compatible with thermal print head. Effectively removes dirt, ink and contamination buildup on thermal print heads.
If the hot water soak did not unclog the print head, place the cartridge printer head in isopropyl alcohol and allow it to soak overnight. Use a damp paper towel to wipe off the print head area and dry carefully.
Otherwise use a printer head cleaning solution recipe of 50% water and 50% rubbing alcohol. We also like a homemade printhead cleaning solution that is 8-parts Windex to 2-parts rubbing alcohol. This printer head cleaning fluid works like a charm and it`s cheap to make!
Soak the Printhead

Fill a bowl with warm water (or a mixture of water and vinegar to clean the printhead) and place the printhead directly in it. Let it sit for five minutes or so. Pull the printhead out of the water and use a lint-free cloth or paper towel to remove the dried ink.

Print head stepper motor – A stepper motor moves the print head assembly (print head and ink cartridges) back and forth across the paper. Some printers have another stepper motor to park the print head assembly when the printer is not in use.
Print head cleaning uses both color and black ink. To avoid wasting ink, clean the print head only if print quality declines (for example, if the printout is blurry or the color is incorrect or missing).
The ink tank feeds its liquid ink down to the separate printhead inside the printer which in turn dispenses the ink in the form of droplets onto the page to form text or images. Sometimes, the ink tank sits directly on top of and directly feeds into the printhead, such as with Epson and Canon Printers.
Print head cleaning uses both color and black ink. To avoid wasting ink, clean the print head only if print quality declines (for example, if the printout is blurry or the color is incorrect or missing).
An ink cartridge is the part that will contain the ink, while a printhead is the part in an inkjet printer that will spray the ink onto the paper.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Print head sponges
ANSWER : Yes, but Epson won’t sell them to you. If you can figure out how to get to them, you can just take them out and wash them in hot water. Otherwise, Google how to reset the warning message on your model. The tanks hold much more ink than the warning permits.

Read Full Q/A … :

Epson Stylus C88+

Removing the print head on a Pixma MX 475?
ANSWER : Take out the ink tanks. On the right side there is a plastic release lever. Lift it up and the heads will unlock. Reach in and remove the heads. Take it to the sink and run hot water through the screens on top and then flip it over and run hot water over the heads. Repeat a few times until the water is clear. Reinstall and try again. It might take a couple pages for the print to look good.

Read Full Q/A … :

Epson Stylus C88+

print heads
ANSWER : Try this: http://support.hp.com/us-en/document/c04293162

Read Full Q/A … :

Epson Stylus C88+

Paper jam in front of print head. HELP URGENT Please
ANSWER : I am 99% sure you don’t have a problem with a sensor. Having no idea what you do in the cleaning process, and not being able to look at the printer, there is no way to help or advise you.

Read Full Q/A … :

Epson Stylus C88+

Epson Artisan 835 print head cleaning question
ANSWER : I had the same problem. After reading the comments, I tried Liquid Wrench spray. 1st try got about sixty percent improvement. Tried again this time I let it set for about 10 min then did a head cleaning. Completely solved the problem. I am a little concerned about its use on plastic. So far so good.

Read Full Q/A … :

Epson Stylus C88+

can't align print head horizontally despite running program
ANSWER : Don’t call that number, it’s a phishing scam number as far as I can tell. Last thing you want to do is have them remote into your computer (they may try hacking you in the background to try & steal bank info/saved passwords) or give them a CC number for tech help since they are not directly affiliated with Epson. As far as Epson’s site shows there is no toll free tech line, only 2 800s listed on their site and 1 is presales other is for supply orders.

Read Full Q/A … :

Epson Stylus C88+

when printing front and back, the front will print well but the back will fade
ANSWER : It happens because second side voltage is much higher and the board breaks. Are you getting this issue in auto duplex only, or same error you are getting when you print second side manually?

Read Full Q/A … :

Epson Stylus C88+

Need help for Epson Stylus color 3000 print head?
ANSWER : I need help changing the print head in my Epson 3000 – I have 2 printers – one will not stay in alignment and the other black ink is plugged and I have soaked it and cannot get it to budge.

Read Full Q/A … :

Epson Stylus C88+