Brother Compactronic I

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Slide the print head until it is at the end of the rail. Push the print head unit towards the back of the device and lift the unit from the back rail. Gently release the other end of the print head to remove it from the front rail.
What is a printhead? The answer is simpler than you may imagine. The printhead is a component in a printer that houses ink cartridges. It`s typically located under the cover of your printer, and it can become clogged with ink over time.
The sponge end of a blocked printer head can be cleaned with only one liquid other than water. This liquid is isopropyl alcohol. Isopropyl alcohol isn`t strong enough to melt the sponge but is still strong enough to dissolve the ink inside the blocked printer head.
The printhead is a component in a printer that houses ink cartridges. It`s typically located under the cover of your printer, and it can become clogged with ink over time.
Every inkjet printer contains at least one printhead that applies ink onto paper and forms a document. Some printers contain two printheads, one for black and one for colour ink, whereas other printers may contain a separate printhead for each ink cartridge.
An error in the cartridges, the heads clogged by dry ink, a very low level in your consumables, a bad connection between the computer and the printer, a damaged cable, a jam in the print queue…, there are many reasons why your Brother printer may stop printing or print poorly even though you have not jumped the ink …
Remove the toner cartridge and gently wipe to remove any dust or toner underneath with a dry cloth. If you notice excess toner inside the print device, it may be possible to remove it using a vacuum that is specifically designed to capture fine dust particles like toner powder. These vacuums can be costly, however.
If your printer or plotter head is built into the printer cartridges, you change your printhead every time you change the ink. If the printheads are built into the printer or plotter, they`re likely to require replacement after long-term use.
Soak the Printhead

Fill a bowl with warm water (or a mixture of water and vinegar to clean the printhead) and place the printhead directly in it. Let it sit for five minutes or so. Pull the printhead out of the water and use a lint-free cloth or paper towel to remove the dried ink.

An error in the cartridges, the heads clogged by dry ink, a very low level in your consumables, a bad connection between the computer and the printer, a damaged cable, a jam in the print queue…, there are many reasons why your Brother printer may stop printing or print poorly even though you have not jumped the ink …

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Need help for Epson Stylus color 3000 print head?
ANSWER : I need help changing the print head in my Epson 3000 – I have 2 printers – one will not stay in alignment and the other black ink is plugged and I have soaked it and cannot get it to budge.

Read Full Q/A … :

Brother Compactronic I

Removing the print head on a Pixma MX 475?
ANSWER : Take out the ink tanks. On the right side there is a plastic release lever. Lift it up and the heads will unlock. Reach in and remove the heads. Take it to the sink and run hot water through the screens on top and then flip it over and run hot water over the heads. Repeat a few times until the water is clear. Reinstall and try again. It might take a couple pages for the print to look good.

Read Full Q/A … :

Brother Compactronic I

when printing front and back, the front will print well but the back will fade
ANSWER : It happens because second side voltage is much higher and the board breaks. Are you getting this issue in auto duplex only, or same error you are getting when you print second side manually?

Read Full Q/A … :

Brother Compactronic I

Paper jam in front of print head. HELP URGENT Please
ANSWER : I am 99% sure you don’t have a problem with a sensor. Having no idea what you do in the cleaning process, and not being able to look at the printer, there is no way to help or advise you.

Read Full Q/A … :

Brother Compactronic I

Epson Artisan 835 print head cleaning question
ANSWER : I had the same problem. After reading the comments, I tried Liquid Wrench spray. 1st try got about sixty percent improvement. Tried again this time I let it set for about 10 min then did a head cleaning. Completely solved the problem. I am a little concerned about its use on plastic. So far so good.

Read Full Q/A … :

Brother Compactronic I

can't align print head horizontally despite running program
ANSWER : Don’t call that number, it’s a phishing scam number as far as I can tell. Last thing you want to do is have them remote into your computer (they may try hacking you in the background to try & steal bank info/saved passwords) or give them a CC number for tech help since they are not directly affiliated with Epson. As far as Epson’s site shows there is no toll free tech line, only 2 800s listed on their site and 1 is presales other is for supply orders.

Read Full Q/A … :

Brother Compactronic I

print heads
ANSWER : Try this: http://support.hp.com/us-en/document/c04293162

Read Full Q/A … :

Brother Compactronic I

Print head sponges
ANSWER : Yes, but Epson won’t sell them to you. If you can figure out how to get to them, you can just take them out and wash them in hot water. Otherwise, Google how to reset the warning message on your model. The tanks hold much more ink than the warning permits.

Read Full Q/A … :

Brother Compactronic I