Unknown Printer

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

If the printer has been printing continuously for a long time, the Print Head Holder may not move to the center since the Print Head may overheat. Opening the Top Cover while printing moves the Print Head Holder to the right. Close the Top Cover, and reopen it after printing finishes.
If your Canon printer isn`t recognising a compatible ink cartridge, this may be because the data on the cartridge chip is stamped with an empty status before it was remanufactured. Hold down the stop / cancel button for 5 seconds to bypass the `ink has run out` message and your cartridge should work.
Verify the ink cartridge(s) is inserted properly. Some cartridges snap in place, and if they are not inserted fully, the printer won`t print anything. If a lever is moved from its original position to allow for installation of ink cartridges, ensure it is returned to its original position.
Press the button on the chip-reset tool for several seconds until the LED light on the device goes off. Then, unlock the reset tool from the cartridge. Use the resetter with other cartridges and install them back into the corresponding slots in your printer. Voila!
1. There isn`t a universal name, and different printers have different configurations. Some have the cartidges in a fixed location, some plug into the print head. If they plug into the print head, the moving piece that holds the cartridges and print head is sometimes called a carriage.
An inkjet spittoon is a component in inkjet printers that collects the ink that is removed from the cartridge when the inkjet is primed. This spittoon (sometimes called a reservior) can be either a plastic tray or a piece of foam that absorbs the excess ink.
If there is plenty of ink and the printer does not print, clean the Print Head then print the nozzle check pattern to ensure ink is ejected properly. If the problem is not resolved after performing Print Head Cleaning twice, carry out the Print Head Deep Cleaning.
The print head holder will not move unless the power is on. If the ON lamp is not lit, close the print head cover and turn the printer on. While the ON lamp is flashing, the machine is initializing. Wait until the ON lamp stops flashing and remains lit, and then open the print head cover again.
The print head holder will not move unless the power is on. If the ON lamp is not lit, close the print head cover and turn the printer on. While the ON lamp is flashing, the machine is initializing. Wait until the ON lamp stops flashing and remains lit, and then open the print head cover again.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

How to reset ink cartridge Canon Pixma MG6320
ANSWER : Your post is a bit confusing. You don’t reset the chip, you pull off the old one and replace it with the one they gave you.

Read Full Q/A … :
Unknown Printer

Canon pixma – ink absorber almost full
ANSWER : They are on the bottom of the printer. If you want to clean them, you can take them out and wash them in hot tap water. Wring them out like a sponge. You will need to reset the printer. http://jezpinions.blogspot.com/2012/03/canon-mg6150-ink-absorber-reset-error.html

Read Full Q/A … :
Unknown Printer

replacing waste ink absorber on Canon Pixma ip6000
ANSWER : ditto, ditto & ditto

Read Full Q/A … :
Unknown Printer

Full Ink Tank in Canon Pixma ip4000
ANSWER : It had been exactly the same subject, could not find an appropriate broker and process for earnings finally had to rummage through the Web, and there I came across this page http://optioninvest.org .Possibly you’ll find there is a therapy to your condition, thanks for the fascination!))

Read Full Q/A … :
Unknown Printer

Canon Pixma iP8720 Ink Compartment Stuck
ANSWER : Here are some solutions you can try. http://fix-your-printer.blogspot.com/2013/01/how-to-fix-error-6a81-on-canon-printers.html

Read Full Q/A … :
Unknown Printer

Fat Black ink fade out
ANSWER : Dear friend

Read Full Q/A … :
Unknown Printer

Reset ink absorber full
ANSWER : Free download of resetter here http://www.k58n.com/3ammresetter/canonresetter/410.html

Read Full Q/A … :
Unknown Printer

ip3000 pixma fried with 240 volts
ANSWER : You will probably need a power supply and possibly a control board (unless it survived). There may be more than that which fried as well…without doing an electrical diagnostics it’s hard to say.

Read Full Q/A … :
Unknown Printer