Phaser 8200, Paper Jam, paper not feeding through

Unknown Printer

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Small fragments of sticky label material commonly get torn off and stuck within your printer, collecting dust and causing a jam. Shut the printer off, get a flashlight, and try to see inside. Make sure no label fragments have jammed up your printer before proceeding.

Make sure that the friction pad, paper feed roller or registration roller is clean. See Cleaning the Friction Pad and Paper Feed Roller and Cleaning the Registration Roller. Check that paper was not added while there was still some left in the tray. Only add paper when there is none left in the tray.

A paper feed issue can occur for several reasons, such as dusty or contaminated paper rollers, the condition of the paper in the tray, or even issues with the software.

If the paper is even slightly askew, the rollers will pick it up a little crooked, and — guess what — the crooked sheet will immediately get jammed. So even though there`s no paper stuck when you start printing, the loose paper guides are ensuring that a sheet gets jammed whenever the printer starts doing its thing.

Paper Handling

Reseat the paper currently loaded into your copier`s paper trays. Frequent paper jams often indicate a problem with how you loaded the paper into the tray. Sometimes simply removing the paper stack and reloading it into the tray can resolve the problem.

Do a hard reset on your printer. To do this you just need to turn off your printer, unplug for a few minutes and then plug the printer again. If that still doesn`t work, try turning the printer and your computer off, and then start it back up again. Try uninstalling and then reinstalling your printer driver.

Over time, paper absorbs and loses moisture which causes it to warp, or not lie perfectly flat. This can create print quality issues like jamming and is something to consider when using a printer that hasn`t been used for a while.

If the paper feed rollers are dirty or paper powder is attached to it, paper may not be fed properly. In this case, clean the paper feed rollers. Cleaning will wear out the paper feed rollers, so perform this only when necessary. Make sure that the power is turned on and remove any paper from the rear tray.

Make sure your paper meets the specifications for your product. If paper dust builds up on the rollers, they may lose traction and become unable to feed paper properly. Clean the paper guide. If roll paper does not feed, cut the end straight across and uncurl it by rolling it backward, if necessary.

During a print job, the printer stops feeding pages, and a Paper Jam error message displays on the printer control panel. This indicates that paper might be jammed inside the printer. note: Paper jams can be real or false. The printer might report a paper jam even when there is no jammed paper.

Try moving the router and printer closer together.

Switching to a wired connection, then back to wireless, can sometimes work as well. Persistent print problems might be a sign that it`s time for a new machine.

A Print Head Clean is performed from the Printer Control Panel under the Main menu. Press the button with the 6 ink channels and select a Print Head Clean.

Loading paper that is stuck together, frayed, curled or bent can cause a jam. Overloading the paper tray, loading different thicknesses of paper in the tray or using paper that isn`t appropriate for your particular printer can all result in a jammed printer.

Dust, paper fiber, and other debris might accumulate on the paper feed rollers and cause paper jams and paper feed issues. Clean the rollers inside the printer, and then try to print again. Turn off the printer, and then disconnect the power cord.

The paper has holes along both sides that fit over the sprockets located on the feeder wheel. When the wheel turns, it feeds the paper into the printer. The holes are torn off the paper after the printout is complete. And, yes, printers still use this type of feeder mechanism.

There are different methods of paper feeding. With dot matrix printers, paper is often feed through pins on a wheel that grab and slowly move paper through the printer. With inkjet and other page printers, paper is fed through the printer with rollers that grab and move the paper through the printer.

General Specifications

Since the Hi-Speed USB interface is fully upwardly compatible with USB 1.1, it can be used at USB 1.1. USB and the network can be used at the same time.

This may be caused by pieces of paper or foreign matter in the machine, or paper not loaded correctly.

The hard reset helps you restore your Canon printer back to its default factory configuration. Here`s how to perform a hard reset: Step 1: Press and hold the “Stop” button on your Canon printer until you hear the alarm ringing. Step 2: Release the “Start” button only after the alarm flashes or rings at least 19 times.

Shut the printer off, get a flashlight, and try to see inside. Make sure no label fragments have jammed up your printer before proceeding. You might need to check underneath the printer and shake it out to dislodge any loose paper or other debris that may have gotten stuck inside.

This issue always happens on various printers including Canon, Ricoh, Epson, Brother, or HP. The common reasons for this issue are various, for instance, the paper input tray is overloaded, dust or moisture can affect the paper feed or paper pick rollers, the printer driver is old, etc.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.

ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.

Read Full Q/A … :
Unknown Printer

Canon mx410 Paper jam message, but no paper jam?!

ANSWER : I have exactly the same problem, no answers 😳

Read Full Q/A … :
Unknown Printer

hp 8600 pro when power on, paper jam message appear but there is no paper jam in the tray

ANSWER : Hp 8180 Photosmart All In One code keeps says paper jam and carriage jam when neither are jammed. I followed all the recommended things to do. I live in Raleigh NC any place to take this or any suggestion.

Read Full Q/A … :
Unknown Printer

Paper Jam and carriage jam code when nothing is jammed

ANSWER : Did you try cleaning the encoder strip that runs through the cartridge assy.? Use Window Cleaner on a paper towel. Also, check inside on the right. I’ve seen a lot of times where there is a folded up scrap of paper that stops the carriage from going all the way to the right.

Read Full Q/A … :
Unknown Printer

Paper Jam error but no paper jam

ANSWER : Obviously you didn’t get all the paper cleared out. There is a small scrap in the paper path causing the jam when the paper hits it. You can try clearing it out by inserting something stiff like a piece of file folder from the back of the printer into the paper path and pushing the offending piece out that way.

Read Full Q/A … :
Unknown Printer

Canon Pixma Printer Paper Does Not Feed Properly/"No Paper" Error Occurs?

ANSWER : Pretty much useless advice. I also have serious doubts about someone who is obviously not fluent in the English language.

Read Full Q/A … :
Unknown Printer

Phaser Jams every time code: 0,006.74

ANSWER : http://www.support.xerox.com/support/phaser-8560mfp/support/enus.html

Read Full Q/A … :
Unknown Printer

Keep getting a paper jam message. There is no jam.

ANSWER : You can quit wondering. Parts are unavailable. I’ve seen posts where people have 3D printed the parts or machined them out of metal.

Read Full Q/A … :
Unknown Printer