HP DeskJet 610C

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

A paper feed issue can occur for several reasons, such as dusty or contaminated paper rollers, the condition of the paper in the tray, or even issues with the software.
You need to ensure your HP printer has enough paper, ink, or toner, and it is not stuck on paper jam. Also, check the status of your printer cartridge and try replacing it with a new one if it is not good enough. In some cases, your HP printer stops printing after you replace its parts.
One sensor is located in the printer carriage. A second sensor—the Auto Sense sensor—is located in the back of the printer near the paper `clean out` area. Each sensor performs a specific set of media detection functions.
There are different methods of paper feeding. With dot matrix printers, paper is often feed through pins on a wheel that grab and slowly move paper through the printer. With inkjet and other page printers, paper is fed through the printer with rollers that grab and move the paper through the printer.
If the paper feed rollers are dirty or paper powder is attached to it, paper may not be fed properly. In this case, clean the paper feed rollers. Cleaning will wear out the paper feed rollers, so perform this only when necessary. Make sure that the power is turned on and remove any paper from the rear tray.
If your printer is running low on ink, it may start printing blank pages. To check your ink levels, go to your printer`s control panel and select the Ink Levels option. Whenever the ink levels are low, replace the cartridges with new ones. You can also try shaking the cartridge gently to redistribute the ink.
Sheet feeder: Holds the blank paper and automatically feeds the paper during printing.
The printer`s rollers are the ones responsible for pulling in the sheets in the input tray.
Rotating the roller by turning the deep side of the drive axis clockwise (1), wipe the roller in the direction of the arrow from the front to the back. Clean the roller until there is no visible dirt or dust on the entire circumference of the paper transfer roller. Visually check that there is no dirt or dust.
When it isn`t working properly, the quality of your prints can suffer. Signs of a bad transfer roller include streaking, squealing, jamming and odors emanating from the printer. Troubleshoot your transfer rollers to restore your prints to their normal high quality.
The feed roller in combination with the feed plate pushes the sliver against the opening roller. The opening roller rotates much faster than the feed roller. This means the fibres in the sliver are hooked by the saw tooth or pins and separated under a high draft ratio into individual fibres by the opening roller.
Paper Feed Rollers

Created with a blending technology developed based on our extensive experience, these materials offer both a high friction coefficient retaining characteristic and superb abrasion resistance. We also mass-produce belt-shaped samples, in addition to ordinary rolls.

This is often caused by the fact the pick-up roller is worn out. The layer of rubber around this plastic part overtime gets too smooth, preventing paper from feeding properly into the printer. This fix is not really hard, will take no more than half an hour and costs around 10,- (Euro or Dollar).
Issue description

A “Load Paper” intervention message appears on the printer display even when there is paper loaded in the tray. This error message means the printer is not detecting any paper on the tray. The same intervention message will appear when: The tray is empty.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.
ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.

Read Full Q/A … :

HP DeskJet 610C

Canon Pixma Printer Paper Does Not Feed Properly/"No Paper" Error Occurs?
ANSWER : Pretty much useless advice. I also have serious doubts about someone who is obviously not fluent in the English language.

Read Full Q/A … :

HP DeskJet 610C

HP psc 1210 Wont Feed Paper
ANSWER : This printer seems to have special problems with paper feed asy. When functioning works

Read Full Q/A … :

HP DeskJet 610C

HP Laserjet 6MP wont feed paper
ANSWER : I had a similar paper pickup problem on laserjet 6mp. The printer would go through start-up sequence fine but when it received a print job you could here the main gears/rollers turning but no clicking from paper pickup solenoid, then eventually error lights would come one . I incorrectly assumed it was an error with the paper pickup mechanism and wasted a whole day taking the printer apart and replacing the paper pick mechanism. Long story short, if I had bothered to figure out the secondary error light codes from the start, I would have realized it was just a bad fuser and would not have wasted so much time.

Read Full Q/A … :

HP DeskJet 610C

paper drive wont accept paper
ANSWER : There is probably a small scrap of paper stuck at the left edge of the paper path. The paper hits it and skews to the left. The smaller size bypasses it. You need to shove something stiff, like a piece of file folder, down the paper path and attempt to dislodge it.

Read Full Q/A … :

HP DeskJet 610C

Error Message "Paper out" when paper loaded
ANSWER : Check your paper tray settings as printer may be looking for paper from the manual feed tray on top of printer.

Read Full Q/A … :

HP DeskJet 610C

Paper feeds straight through without printing on an Epson R2400
ANSWER : I was able to get it to print the internal test page by holding down the sheet paper feed button while turning the machine on — then continuing to hold the sheet paper feed button. It took several attempts, feeding a page straight through, but eventually it caught the sheet and printed. So it may be a timing issue as others have mentioned. It could still mean that the feed rollers are worn out. The back side of the large D-shaped feed roller has visible abrasion on it. The abrasion is difficult to see as the roller does not stay with the flat side exposed.

Read Full Q/A … :

HP DeskJet 610C

Multiple paper feed
ANSWER : Most likely the pickup roller solenoid is sticking. The way it works is the solenoid energizes, pulling down a metal plate that releases the pickup roller. There is some foam on the base to quiet the clicking sound. The foam deteriorates and the plate sticks to the gooey residue. This allows the pickup roller to continue to turn instead of stopping after one revolution when the plate springs back up. That results in multiple paper being fed. Solution is to find the solenoid, which is at the end of the pickup roller shaft. Remove the sticky foam and preferably replace it with some thin sticky backed felt. You can find it at a hardware store as it is used on the bottom of chair legs.

Read Full Q/A … :

HP DeskJet 610C