Lexmark Jetprinter 4076
How to Identify and Fix Common Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
Open the tray and do one or more of the following: Check for paper jams or misfeeds. Check if the paper size indicators on the paper guides are aligned with the paper size indicators on the tray. If you are printing on custom‑size paper, then make sure that the paper guides rest against the edges of the paper.
If roll paper does not feed, cut the end straight across and uncurl it by rolling it backward, if necessary. Then reload the paper. If thick media does not feed, make sure you are loading it straight into the product, not at an angle. If paper jams when you print on both sides of the paper, try loading fewer sheets.
Select > Paper Setting > paper source > Print Adjustments > Paper Feed Adjust.
Remove the stack of paper from the tray. Check for obstructions inside the tray. Use a flashlight to view the mechanism inside the tray to make sure that nothing blocks the paper from engaging with the rollers. Even small pieces of paper can cause paper feed issues.
Paper Overloading
Because many desktop inkjet printers are top-loading, it can be easy to overload the tray.
If the paper feed rollers are dirty or paper powder is attached to it, paper may not be fed properly. In this case, clean the paper feed rollers. Cleaning will wear out the paper feed rollers, so perform this only when necessary. Make sure that the power is turned on and remove any paper from the rear tray.
If there is paper in the tray but the printer is not picking the paper, open the tray and flip the paper stack over. Load a fresh ream of paper and observe whether the issue remains. If the issue persists, remove the whole tray out and inspect the bottom of the tray for any paper debris or obstructions.
Restart your printer. In some cases, a simple restart can fix the issue. Unplug the printer and check if there is any paper stuck in the machine, and if the toner is installed correctly. If all seems fine leave the printer disconnected for half a minute, then reconnect it and resume the print job.
The paper feeding mechanism includes a drive gear coaxially coupled to a shaft of drive roller for transferring a sheet to a printing zone, a feed gear coaxially coupled to a shaft of the feed roller and operating to align the sheet transferred from the drive roller, and a discharge gear coaxially coupled to a shaft of …
Make sure that the paper size and type matches with the paper in the tray. False error messages can result from incorrect media settings in the driver or on the printer. If the tray is full and no paper jam is associated with the error, try cleaning the pick rollers.
Make sure you are pointing the Bypass tray from the printing settings. Make sure you fill the Bypass tray ONCE you`ve sent the files to the printer. Make sure the user have permissions to print from the Bypass tray. Make sure your Bypass tray is activated in the Printer`s parameters.
Make sure you are pointing the Bypass tray from the printing settings. Make sure you fill the Bypass tray ONCE you`ve sent the files to the printer. Make sure the user have permissions to print from the Bypass tray. Make sure your Bypass tray is activated in the Printer`s parameters.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.
ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.
Read Full Q/A … :
Lexmark Jetprinter 4076
Canon Pixma Printer Paper Does Not Feed Properly/"No Paper" Error Occurs?
ANSWER : Pretty much useless advice. I also have serious doubts about someone who is obviously not fluent in the English language.
Read Full Q/A … :
Lexmark Jetprinter 4076
Brother Hl-2040 paper over feed
ANSWER : Your instructions saved me..I had the board off 3 times before i saw your pix….thanks so much!
Read Full Q/A … :
Lexmark Jetprinter 4076
Paper feed
ANSWER : Judging by your other post, you must have read that you need to remove the laser scanner assy and lubricate the spinning mirror shaft. Good luck.
Read Full Q/A … :
Lexmark Jetprinter 4076
Paper Feed Problem on HP R80
ANSWER : In the last examination it is our origination of death which chooses our responses to all the inquiries life puts to us. The most pleasant spot to be is in somebody’s idea; the most secure spot to be is in somebody’s petitions.
Read Full Q/A … :
Lexmark Jetprinter 4076
paper drive wont accept paper
ANSWER : There is probably a small scrap of paper stuck at the left edge of the paper path. The paper hits it and skews to the left. The smaller size bypasses it. You need to shove something stiff, like a piece of file folder, down the paper path and attempt to dislodge it.
Read Full Q/A … :
Lexmark Jetprinter 4076
Error message to load paper and push OK, but not out of paper
ANSWER : I assist the binary options for a long time, and only half this past year I decided to alter the strategy for a better, she called for help Bing and he gave me this web site http://bestoptionstrategies.net .Now I focus on the suitable technique for themselves, and things gone up. I think everybody else faced with this particular problem. I believe my estimation will soon be helpful to you.
Read Full Q/A … :
Lexmark Jetprinter 4076
Multiple paper feed
ANSWER : Most likely the pickup roller solenoid is sticking. The way it works is the solenoid energizes, pulling down a metal plate that releases the pickup roller. There is some foam on the base to quiet the clicking sound. The foam deteriorates and the plate sticks to the gooey residue. This allows the pickup roller to continue to turn instead of stopping after one revolution when the plate springs back up. That results in multiple paper being fed. Solution is to find the solenoid, which is at the end of the pickup roller shaft. Remove the sticky foam and preferably replace it with some thin sticky backed felt. You can find it at a hardware store as it is used on the bottom of chair legs.
Read Full Q/A … :
Lexmark Jetprinter 4076