Unknown Printer

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

your pickup roller is dirty and the printer can`t grab a piece of paper. it will say paper jam when it does this. get a drop of dishsoap and clean the pickup roller of your printer with this. scrape at it with your fingernail to get the roller clean and wipe it off with a damp washcloth.
Small fragments of sticky label material commonly get torn off and stuck within your printer, collecting dust and causing a jam. Shut the printer off, get a flashlight, and try to see inside. Make sure no label fragments have jammed up your printer before proceeding.
Make sure that the friction pad, paper feed roller or registration roller is clean. See Cleaning the Friction Pad and Paper Feed Roller and Cleaning the Registration Roller. Check that paper was not added while there was still some left in the tray. Only add paper when there is none left in the tray.
Contrary to its name, there is nothing supernatural or spooky about a ghost jam. Instead, ghost jamming refers to an issue whereby the copier reports a paper jam even though there is no paper being physically jammed within the copier. Such an occurrence is also known as a fake jam or a false jam.
Step one: Perform a power reset

Unplug the power cord from the wall outlet. Wait at least 15 seconds. Plug the power cord back into the wall outlet. Reconnect the power cord to the rear of the product.

During a print job, the printer stops feeding pages, and a Paper Jam error message displays on the printer control panel. This indicates that paper might be jammed inside the printer. note: Paper jams can be real or false. The printer might report a paper jam even when there is no jammed paper.
Ghost prints happen when the drum or fuser unit within your printer become faulty. Because a fault with this element won`t heat the particles of the toner to a high enough temperature, the marks being made on the paper are much lighter in colour and appear more faded than typical documents.
Dust, dirt, or debris: Not cleaning the HP Printer can also result in a paper jam error. So, if you find that no paper is stuck but a paper jam error showing, you must check for the dirt or dust on the device.
Slide the paper all the way into the printer. The leading edge of the paper will stop at the Paper Drive Roller. Locate the Paper Sensor/OOPs sensor on the right side of the paper path. It can be seen from the top of the printer with the Top Cover open and has red, black, and blue wires attached to it.
Slide the paper all the way into the printer. The leading edge of the paper will stop at the Paper Drive Roller. Locate the Paper Sensor/OOPs sensor on the right side of the paper path. It can be seen from the top of the printer with the Top Cover open and has red, black, and blue wires attached to it.
Preventing a printer paper jam

Overfilling the paper tray is frequently causes paper jams. Many printers have sliding mechanisms that allow different types and sizes of paper to be fed into the printer. If the slider is not correctly positioned, it can cause a paper jam. Use standard office paper.

Slide the paper all the way into the printer. The leading edge of the paper will stop at the Paper Drive Roller. Locate the Paper Sensor/OOPs sensor on the right side of the paper path. It can be seen from the top of the printer with the Top Cover open and has red, black, and blue wires attached to it.
Dust, dirt, or debris: Not cleaning the HP Printer can also result in a paper jam error. So, if you find that no paper is stuck but a paper jam error showing, you must check for the dirt or dust on the device.
Dust, dirt, or debris: Not cleaning the HP Printer can also result in a paper jam error. So, if you find that no paper is stuck but a paper jam error showing, you must check for the dirt or dust on the device.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.
ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.

Read Full Q/A … :
Unknown Printer

Paper Jam error but no paper jam
ANSWER : Obviously you didn’t get all the paper cleared out. There is a small scrap in the paper path causing the jam when the paper hits it. You can try clearing it out by inserting something stiff like a piece of file folder from the back of the printer into the paper path and pushing the offending piece out that way.

Read Full Q/A … :
Unknown Printer

Paper Jam and carriage jam code when nothing is jammed
ANSWER : Did you try cleaning the encoder strip that runs through the cartridge assy.? Use Window Cleaner on a paper towel. Also, check inside on the right. I’ve seen a lot of times where there is a folded up scrap of paper that stops the carriage from going all the way to the right.

Read Full Q/A … :
Unknown Printer

Canon mx410 Paper jam message, but no paper jam?!
ANSWER : I have exactly the same problem, no answers 😳

Read Full Q/A … :
Unknown Printer

hp 8600 pro when power on, paper jam message appear but there is no paper jam in the tray
ANSWER : Hp 8180 Photosmart All In One code keeps says paper jam and carriage jam when neither are jammed. I followed all the recommended things to do. I live in Raleigh NC any place to take this or any suggestion.

Read Full Q/A … :
Unknown Printer

Keep getting a paper jam message. There is no jam.
ANSWER : You can quit wondering. Parts are unavailable. I’ve seen posts where people have 3D printed the parts or machined them out of metal.

Read Full Q/A … :
Unknown Printer

Paper jam in tray 2 (but no paper pulled from tray) also M476DN models
ANSWER : Isopropyl alcohol is not recommended for rubber rollers. It dries out the rubber and hasten it’s cracking and breaking. It will do nothing to restore the grip. Those rollers are really hard to replace. It would be easy if that dumbass secondary menu really worked. None of the techs I’ve spoke to ever got into it. Everyone I know sends a print job and listens for the roller to rotate into position where you can pull it off.

Read Full Q/A … :
Unknown Printer

message error: ADF paper jam
ANSWER : There is a thin plastic arm that the paper pushes on. It is spring loaded. If it doesn’t return and unblock the sensor after the paper passes it, you get the paper jam warning. I’m guessing that is the spring you are referring to.

Read Full Q/A … :
Unknown Printer