Lexmark Optra T

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

A 202.05 paper jam error code appears on the printer. One of the possible causes of this issue is the Exit Sensor is blocked too long and was not able to clear the sheet. Another possible cause can be a loose back door, tape on reverse solenoid pad (as shown in the image below), or a worn/contaminated Fuser.
If the paper is even slightly askew, the rollers will pick it up a little crooked, and — guess what — the crooked sheet will immediately get jammed. So even though there`s no paper stuck when you start printing, the loose paper guides are ensuring that a sheet gets jammed whenever the printer starts doing its thing.
Small fragments of sticky label material commonly get torn off and stuck within your printer, collecting dust and causing a jam. Shut the printer off, get a flashlight, and try to see inside. Make sure no label fragments have jammed up your printer before proceeding.
Common causes of paper jams include: Damaged rollers. Inserting paper that is incompatible with the printer. Loading the paper incorrectly.
Slide the paper all the way into the printer. The leading edge of the paper will stop at the Paper Drive Roller. Locate the Paper Sensor/OOPs sensor on the right side of the paper path. It can be seen from the top of the printer with the Top Cover open and has red, black, and blue wires attached to it.
Do a hard reset on your printer. To do this you just need to turn off your printer, unplug for a few minutes and then plug the printer again. If that still doesn`t work, try turning the printer and your computer off, and then start it back up again. Try uninstalling and then reinstalling your printer driver.
With dot matrix printers, paper is often feed through pins on a wheel that grab and slowly move paper through the printer. With inkjet and other page printers, paper is fed through the printer with rollers that grab and move the paper through the printer.
Step one: Perform a power reset

Unplug the power cord from the wall outlet. Wait at least 15 seconds. Plug the power cord back into the wall outlet. Reconnect the power cord to the rear of the product.

Improperly Loading Paper into the Device

Loading paper that is stuck together, frayed, curled or bent can cause a jam. Overloading the paper tray, loading different thicknesses of paper in the tray or using paper that isn`t appropriate for your particular printer can all result in a jammed printer.

It`s important to replace the drum promptly when it`s low to avoid any further damage to the printer and to maintain optimal print quality. A bad drum may cause paper jams because it can cause the toner to be unevenly distributed on the paper, leading to jams or misfeeds.
Did you know most copier paper jams are caused by the paper itself? Misaligned paper. When a stack of paper isn`t aligned properly in the machine, it often causes a paper jam issue. When adding a ream of paper, always fan the paper, load carefully and avoid overstuffing the tray.
your pickup roller is dirty and the printer can`t grab a piece of paper. it will say paper jam when it does this. get a drop of dishsoap and clean the pickup roller of your printer with this. scrape at it with your fingernail to get the roller clean and wipe it off with a damp washcloth.
Dust, paper fiber, and other debris might accumulate on the pick rollers and cause paper feed issues. To help prevent paper feed issues, clean the rollers inside the printer and in the duplexer (if equipped). If the other steps in this document fail to resolve the issue, then reset the printer.
Using both hands, put one piece of paper in the manual feed slot until the front edge of the paper touches the paper feed roller. Once the machine has grasped the paper, let go. The side to be printed should be faced up. The machine will hold the paper in place until the print data is sent to the machine.
Adjust the paper guides in the tray to match the size of the paper. Remove the paper, smooth it out, then reload it. If the paper misfeeds, do not use that paper. Remove the moist paper, then replace it with new, dry paper.
The automatic paper type sensor functions when a tray is configured to the. Any Type. or plain type. setting. After it has picked up paper from the tray, the product can detect overhead transparencies, paper.
The transfer belt moves the paper through your printer and passes it across the drum so that the toner can be transferred. Some smaller printers do not have a transfer belt but instead have rollers that act in the same way as a belt.
There are a few things that could be the cause of this problem, including: Empty ink or toner cartridges that need replacing. Ink or toner cartridges that have become dislodged from their proper place. The wrong paper size loaded in the input tray.
Make sure that both your computer and your Lexmark printer are connected to your network. Restart your printer. In some cases, a simple restart can fix the issue. Unplug the printer and check if there is any paper stuck in the machine, and if the toner is installed correctly.
Depending on the setting, printed copies are fed as follows: Side 1 is the surface of the paper printed during one-sided printing, or the surface of the first print during duplex printing. Side 2 is the surface of the paper printed on the back side of Side 1 during duplex printing.
The paper feeding mechanism includes a drive gear coaxially coupled to a shaft of drive roller for transferring a sheet to a printing zone, a feed gear coaxially coupled to a shaft of the feed roller and operating to align the sheet transferred from the drive roller, and a discharge gear coaxially coupled to a shaft of …
Place the paper in your copiers paper tray, so the wording “Copy this side first” is facing up. Only fill the paper up to the fill line which is located on the inner side of the tray. Adjust the tray`s guide back towards the paper. Don`t push the guide too far and buckle the paper.
A paper jam is when paper or other printed material gets stuck or lodged in a printer and cannot eject.
Use of low-quality cartridges

Just as low-quality papers can leave behind paper dust, low quality cartridges can leave behind stray ink and toner. This will not only result in paper jams but also affect output quality.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.
ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.

Read Full Q/A … :

Lexmark Optra T

Rear Paper Feed Blocked On Left Side?
ANSWER : Most times it is something you can’t see, like a small torn scrap of paper. What you can try is to shove a file folder down the path the paper takes. That will push out any offending scrap without having to take the printer apart.

Read Full Q/A … :

Lexmark Optra T

Canon Pixma Printer Paper Does Not Feed Properly/"No Paper" Error Occurs?
ANSWER : Pretty much useless advice. I also have serious doubts about someone who is obviously not fluent in the English language.

Read Full Q/A … :

Lexmark Optra T

Brother Hl-2040 paper over feed
ANSWER : Your instructions saved me..I had the board off 3 times before i saw your pix….thanks so much!

Read Full Q/A … :

Lexmark Optra T

Paper Feed Problem on HP R80
ANSWER : In the last examination it is our origination of death which chooses our responses to all the inquiries life puts to us. The most pleasant spot to be is in somebody’s idea; the most secure spot to be is in somebody’s petitions.

Read Full Q/A … :

Lexmark Optra T

paper drive wont accept paper
ANSWER : There is probably a small scrap of paper stuck at the left edge of the paper path. The paper hits it and skews to the left. The smaller size bypasses it. You need to shove something stiff, like a piece of file folder, down the paper path and attempt to dislodge it.

Read Full Q/A … :

Lexmark Optra T

Paper feed
ANSWER : Judging by your other post, you must have read that you need to remove the laser scanner assy and lubricate the spinning mirror shaft. Good luck.

Read Full Q/A … :

Lexmark Optra T

Error message to load paper and push OK, but not out of paper
ANSWER : I assist the binary options for a long time, and only half this past year I decided to alter the strategy for a better, she called for help Bing and he gave me this web site http://bestoptionstrategies.net .Now I focus on the suitable technique for themselves, and things gone up. I think everybody else faced with this particular problem. I believe my estimation will soon be helpful to you.

Read Full Q/A … :

Lexmark Optra T