HP OfficeJet 6500A
the paper feed mechanism is not longer feeding properly. I can jam a pc. of paper up into the body and if timed just right, the grippers will take it, but would like for it to feed properly. Any suggestions?

How to Identify and Fix Common printer Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

The paper might not be engaged with the feed rollers. The paper-width guide is pressed against the paper stack too tightly. The paper tray is not completely inserted into the product. The paper settings in the print driver do not match the paper loaded in the paper tray.
Printer rollers are the small circular rubber pieces that help feed printer paper through your printer. Over time, they can accumulate dust from the paper and ink residue from printing double-sided pages. To clean your printer rollers, you`ll need to first locate them in your printer.
Paper is housed in the printer`s paper tray, and most trays can be found along the bottom of the printer. There is usually a small notch on the face of the tray that pulls out so you can insert the paper. Within the paper tray, you will notice a guide that can be adjusted to fit your preferred paper length.
Select > Paper Setting > paper source > Print Adjustments > Paper Feed Adjust.
If roll paper does not feed, cut the end straight across and uncurl it by rolling it backward, if necessary. Then reload the paper. If thick media does not feed, make sure you are loading it straight into the product, not at an angle. If paper jams when you print on both sides of the paper, try loading fewer sheets.
Dust, paper fiber, and other debris might accumulate on the paper feed rollers and cause paper jams and paper feed issues. Clean the rollers inside the printer, and then try to print again. Turn off the printer, and then disconnect the power cord.
Continuous form feed and friction feed are the two types of paper feeder mechanisms. Dot matrix printers use continuous form feed, and laser printers use friction feed.
A printer is useless without something to print on, so how the paper gets into a printer seems like a perfect place to start the discussion. The paper enters the printer through a feeder, technically a paper feeder mechanism. The paper feeder mechanism pulls or pushes the paper into the printer.
Before you print, load photo paper or cards into the input tray. Open the input tray door, then pull it toward you to extend the paper tray. Slide the paper width guides to their outermost position. Load the photo paper or card into the paper tray with the short edge forward and the print side down.
A paper feed issue can occur for several reasons, such as dusty or contaminated paper rollers, the condition of the paper in the tray, or even issues with the software.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.
ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.

Read Full Q/A … :

HP OfficeJet 6500A

Canon Pixma Printer Paper Does Not Feed Properly/"No Paper" Error Occurs?
ANSWER : Pretty much useless advice. I also have serious doubts about someone who is obviously not fluent in the English language.

Read Full Q/A … :

HP OfficeJet 6500A

Brother Hl-2040 paper over feed
ANSWER : Your instructions saved me..I had the board off 3 times before i saw your pix….thanks so much!

Read Full Q/A … :

HP OfficeJet 6500A

Paper feed
ANSWER : Judging by your other post, you must have read that you need to remove the laser scanner assy and lubricate the spinning mirror shaft. Good luck.

Read Full Q/A … :

HP OfficeJet 6500A

Paper Feed Problem on HP R80
ANSWER : In the last examination it is our origination of death which chooses our responses to all the inquiries life puts to us. The most pleasant spot to be is in somebody’s idea; the most secure spot to be is in somebody’s petitions.

Read Full Q/A … :

HP OfficeJet 6500A

paper drive wont accept paper
ANSWER : There is probably a small scrap of paper stuck at the left edge of the paper path. The paper hits it and skews to the left. The smaller size bypasses it. You need to shove something stiff, like a piece of file folder, down the paper path and attempt to dislodge it.

Read Full Q/A … :

HP OfficeJet 6500A

Error message to load paper and push OK, but not out of paper
ANSWER : I assist the binary options for a long time, and only half this past year I decided to alter the strategy for a better, she called for help Bing and he gave me this web site http://bestoptionstrategies.net .Now I focus on the suitable technique for themselves, and things gone up. I think everybody else faced with this particular problem. I believe my estimation will soon be helpful to you.

Read Full Q/A … :

HP OfficeJet 6500A

Multiple paper feed
ANSWER : Most likely the pickup roller solenoid is sticking. The way it works is the solenoid energizes, pulling down a metal plate that releases the pickup roller. There is some foam on the base to quiet the clicking sound. The foam deteriorates and the plate sticks to the gooey residue. This allows the pickup roller to continue to turn instead of stopping after one revolution when the plate springs back up. That results in multiple paper being fed. Solution is to find the solenoid, which is at the end of the pickup roller shaft. Remove the sticky foam and preferably replace it with some thin sticky backed felt. You can find it at a hardware store as it is used on the bottom of chair legs.

Read Full Q/A … :

HP OfficeJet 6500A