Xerox WorkCentre 7345
For past 10 days, paper is stuck in fuser after curling.

Experienced technical support provide their insights in answering this question :
Paper curling is caused either by excess heat or toner on the fuser that sticks to the page. I’ve seen it also caused by heavy bands of printing too close to the top of the page.

How to Identify and Fix Common printer Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Paper curl is caused by an excess amount of moisture in the paper. The first step to ensure less paper curl is to store your paper in a cool, dry area. By doing so, you will reduce the amount of moisture and humidity the paper is exposed to. The next step is to always fan the paper before placing in the machine.
High temperatures and high humidity will cause paper to curl. If you don`t use the printer very often, the paper may have been in the paper tray too long. Turn over the stack of paper in the paper tray. Also, fan the paper stack and then rotate the paper 180 degrees in the paper tray.
Usually when that happens, the paper listed in the Print Driver Print menu doesn`t EXACTLY match what is loaded in the tray. Make sure the settings match exactly. The steps to set the paper at the device are HERE . Make sure when you go FILE > PRINT the paper exactly matches what you set at the device.
Paper/cover curl is the result of an increase or decrease in the relative humidity in the environment the books are located. The ideal humidity level to keep paper flat is around 45%RH. Print shops control their climate by adding or reducing the amount of moisture in the air to maintain the 45%RH target.
Curl is defined as the inverse of the radius of curvature of the sheet, and is positive when the printed side is convex. Curl in paper and board can cause problems in a variety of printing and packaging processes.
Gently press on the print`s corners, or whichever side you are trying to straighten up, and they should easily bend until the bottom is completely flat. Keep your fingers in position for 3-5 minutes until the print and the pan have cooled off a bit.
The only possible way to unwarp a 3D print would be re-heating it using a heat gun/hair dryer and trying to nudge it back into shape.
Paper curl occurs, depending on heating conditions at the time or the environment, and where the paper was kept before use.
Configuring Tray Settings at the Control Panel

Touch Tools, then touch Device Settings > Paper Management. Touch Tray Settings, then select a tray. Configure settings as needed. To set the mode, touch Fully Adjustable or Dedicated.

In the depths of winter, RH levels as low as 15-20% are not uncommon. In these conditions, moisture is drawn from the exposed surfaces of stacks of paper and they shrink, but the centre of the paper still has its original moisture content. This causes “tight edges” and the paper begins to curl.
What to use: Since Loose curls tend to be fine, a little external boost from humidity can be of benefit to help define its curls. Too much humidity, however, can cause all hair types to frizz, but especially loose curl types.
Curling is a planar distortion in a paper support in response to changes in relative humidity (Reilly 1986). Factors such as fiber strength, internal bonding, and fiber orientation may affect curling.
Paper curl occurs, depending on heating conditions at the time or the environment, and where the paper was kept before use.
One of the most common causes of filament curling around the nozzle tip is a partial blockage within the nozzle. Over time, filament residue can build up within the nozzle, especially if certain types of filament weren`t extruded properly, resulting in overly thin strands of filament being deposited.
One of the most common causes of filament curling around the nozzle tip is a partial blockage within the nozzle. Over time, filament residue can build up within the nozzle, especially if certain types of filament weren`t extruded properly, resulting in overly thin strands of filament being deposited.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.
ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.

Read Full Q/A … :

Xerox WorkCentre 7345

paper curl problem
ANSWER : Paper curling is caused either by excess heat or toner on the fuser that sticks to the page. I’ve seen it also caused by heavy bands of printing too close to the top of the page.

Read Full Q/A … :

Xerox WorkCentre 7345

Canon Pixma Printer Paper Does Not Feed Properly/"No Paper" Error Occurs?
ANSWER : Pretty much useless advice. I also have serious doubts about someone who is obviously not fluent in the English language.

Read Full Q/A … :

Xerox WorkCentre 7345

Paper Feed Problem on HP R80
ANSWER : In the last examination it is our origination of death which chooses our responses to all the inquiries life puts to us. The most pleasant spot to be is in somebody’s idea; the most secure spot to be is in somebody’s petitions.

Read Full Q/A … :

Xerox WorkCentre 7345

Error Message "Paper out" when paper loaded
ANSWER : Check your paper tray settings as printer may be looking for paper from the manual feed tray on top of printer.

Read Full Q/A … :

Xerox WorkCentre 7345

paper drive wont accept paper
ANSWER : There is probably a small scrap of paper stuck at the left edge of the paper path. The paper hits it and skews to the left. The smaller size bypasses it. You need to shove something stiff, like a piece of file folder, down the paper path and attempt to dislodge it.

Read Full Q/A … :

Xerox WorkCentre 7345

Lexmark paper feed problems
ANSWER : On my X204n Lexmark laser printer, it was doing the same thing you described – basically sounded like it was trying to pick up the paper from the tray and then failing after several seconds. When you’d open the paper tray, the paper looked like it had been partially taken up with some black scuff marks on the paper that lined up with the rollers that take up the paper. I inspected the rollers and although they looked a bit smooth and worn, didn’t seem like they should be a problem. However, this particular model has just a rubber tire almost like a car tire – the rubber can come off the hard plastic wheel on the inner portion. So I popped off the two rubber “tires”, turned them inside out and put them back on. When turned inside out, the rubber looked nice and … rubbery and had a lot more grippy feeling to them. The very first printing attempt after that and the paper sucked up perfectly with no problems. I think the problem is solved! So if you have similar “tires” that take up the paper, try flipping them and see if it works for you too.

Read Full Q/A … :

Xerox WorkCentre 7345

Error message to load paper and push OK, but not out of paper
ANSWER : I assist the binary options for a long time, and only half this past year I decided to alter the strategy for a better, she called for help Bing and he gave me this web site http://bestoptionstrategies.net .Now I focus on the suitable technique for themselves, and things gone up. I think everybody else faced with this particular problem. I believe my estimation will soon be helpful to you.

Read Full Q/A … :

Xerox WorkCentre 7345