Unknown Printer

Experienced technical support provide their insights in answering this question :
Thanks for posting this! I just started experiencing this exact problem with this exact model of printer, and I’m astounded to find a resolution!

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Paper is housed in the printer`s paper tray, and most trays can be found along the bottom of the printer. There is usually a small notch on the face of the tray that pulls out so you can insert the paper.
Creases and folds in the paper are normally due to one of the following conditions: The paper is not correctly loaded in the paper tray. You are printing on a special type of paper or other media. The paper has absorbed too much moisture from the surrounding air.
The paper might not be engaged with the feed rollers. The paper-width guide is pressed against the paper stack too tightly. The paper tray is not completely inserted into the product. The paper settings in the print driver do not match the paper loaded in the paper tray.
With dot matrix printers, paper is often feed through pins on a wheel that grab and slowly move paper through the printer. With inkjet and other page printers, paper is fed through the printer with rollers that grab and move the paper through the printer.
hard copy (printout) … Sometimes referred to as a printout , a hard copy is so-called because it exists as a physical object.
The printer prints on the bottom side of the top sheet of paper loaded in the paper tray. If printing on numbered checks or forms you will need to re-stack the checks or forms in reverse order. When loading the re-stacked checks or forms in the paper tray, place them with the printed side down in the paper tray.
A conductor belt creates an invisible “picture” of both sides of the print job using information it receives from your computer, then sends each side of the page picture to one of two transfuser belts that come together and apply toner as each page runs through the printer.
Roll fold. This type of fold is where each page folds in on itself. It is typically used to produce a trifold leaflet such as a one third A4 leaflet or a DL leaflet. This is where an A4 sheet is folded it to three sections, the right-hand page is folded inwards and then folded in again.
Remove the stack of paper from the tray. Check for obstructions inside the tray. Use a flashlight to view the mechanism inside the tray to make sure that nothing blocks the paper from engaging with the rollers. Even small pieces of paper can cause paper feed issues.
The paper feeding mechanism includes a drive gear coaxially coupled to a shaft of drive roller for transferring a sheet to a printing zone, a feed gear coaxially coupled to a shaft of the feed roller and operating to align the sheet transferred from the drive roller, and a discharge gear coaxially coupled to a shaft of …
Paper is a thin sheet material produced by mechanically or chemically processing cellulose fibres derived from wood, rags, grasses, or other vegetable sources in water, draining the water through a fine mesh leaving the fibre evenly distributed on the surface, followed by pressing and drying.
Paper curl is caused by an excess amount of moisture in the paper. The first step to ensure less paper curl is to store your paper in a cool, dry area. By doing so, you will reduce the amount of moisture and humidity the paper is exposed to. The next step is to always fan the paper before placing in the machine.
Make sure your paper meets the specifications for your product. If paper dust builds up on the rollers, they may lose traction and become unable to feed paper properly. Clean the paper guide. If roll paper does not feed, cut the end straight across and uncurl it by rolling it backward, if necessary.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.
ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.

Read Full Q/A … :
Unknown Printer

paper comes out with fold
ANSWER : Thanks for posting this! I just started experiencing this exact problem with this exact model of printer, and I’m astounded to find a resolution!

Read Full Q/A … :
Unknown Printer

Folding paper
ANSWER : No idea what kind of printer, but what you can try is to shove something thin and stiff down the paper path to dislodge the offending scrap of paper. Try a piece of file folder.

Read Full Q/A … :
Unknown Printer

paper drive wont accept paper
ANSWER : There is probably a small scrap of paper stuck at the left edge of the paper path. The paper hits it and skews to the left. The smaller size bypasses it. You need to shove something stiff, like a piece of file folder, down the paper path and attempt to dislodge it.

Read Full Q/A … :
Unknown Printer

Error message to load paper and push OK, but not out of paper
ANSWER : I assist the binary options for a long time, and only half this past year I decided to alter the strategy for a better, she called for help Bing and he gave me this web site http://bestoptionstrategies.net .Now I focus on the suitable technique for themselves, and things gone up. I think everybody else faced with this particular problem. I believe my estimation will soon be helpful to you.

Read Full Q/A … :
Unknown Printer

Canon Pixma Printer Paper Does Not Feed Properly/"No Paper" Error Occurs?
ANSWER : Pretty much useless advice. I also have serious doubts about someone who is obviously not fluent in the English language.

Read Full Q/A … :
Unknown Printer

Error Message "Paper out" when paper loaded
ANSWER : Check your paper tray settings as printer may be looking for paper from the manual feed tray on top of printer.

Read Full Q/A … :
Unknown Printer

My encolder has come off and i Cant get the screws to come out to open up
ANSWER : torx driver for an hp if thats what you have

Read Full Q/A … :
Unknown Printer