Unknown Printer

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Hope you are well, usually that error message stands for paper jam inside the printer, please check the rear door, remove the tray 2 and check for paper stuck.
Very often a 13.1 Paper Jam Message will appear, instructing the user to check Tray 2 or to check under the toner cartridge. Upon thoroughly checking the printer there is no paper jam to be found anywhere.
Once the printer believes the cartridge has run out of ink you will be presented with either the E13 message or the E16 message that indicates that you need to change the ink cartridge. If this message is being displayed on your printers screen then your printer will stop printing and scanning.
Usually, the error code e31 occurs when there is an improper connection between your printer and the system. This means your computer is finding it hard to establish a connection with your printer, and vice versa.
This jam occurs when residual paper is detected at the Tray 2 feed sensor (SR11). Open Tray 2, remove any jammed paper, and then close the tray. Open and close the upper right door to allow the printer to attempt to clear the jam.
If the LabelWriter appears as Unspecified or Unknown in Devices and Printers on Windows, it usually means that the computer has not identified that device as a printer yet.
How to Resolve the Invalid Amount Code. Resolving error code 13 alerts is quite simple. The user will need to carefully scan through all field inputs and verify that the characters or symbols they put in are appropriate for each field. It`s also important to make sure there aren`t any negatives or incorrect symbols.
ERROR 13 – Paper Jam.
E13 indicates that your pump is taking too long to empty the machine and needs cleaned out.
Cause. Paper is jammed as printer pulled in printed paper.
E, 1, 6 (LED display)

The ink has run out. Replace the ink cartridge and close the paper output cover.

Ink valve is closed.
If you have an Ascent or Venturist model, it will display error code E31 or E3x when the thermal override activates. This post will explore what causes motor heating and describe how to minimize it. I investigated by directly measuring the temperature of the motor in a variety of blending conditions.
This error will occur due to the paper jam inside your printer To fix the error code e03 on your printer, follow the below steps. Start by turning off your Canon Printer TS3122 printer and unplugging the power cord. Now, open the front cover of the printer. Now, slowly pull out the jammed paper inside the printer.
The event code: 13. B9. FF indicates that the printer believes there is a jam at the fuser output sensor, at power on. That means that printer has been power cycled, and the printer detects paper under the fuser output sensor while checking during the boot process.
For example; a 13. A2. D2 indicates that the paper jammed before reaching the tray 2 feed sensor when pulling paper from tray 2. In this case you would look for any jammed paper in or behind tray 2.
Error 13 typically means there is a network connection issue to the target machines.
For example; a 13. A2. D2 indicates that the paper jammed before reaching the tray 2 feed sensor when pulling paper from tray 2. In this case you would look for any jammed paper in or behind tray 2.
The 13.02 error message indicates that paper did not clear the top of page sensor (PS103) within the specified amount of time allotted by the DC Controller. This sensor is located underneath the registration assembly. The jam message may vary depending on the location of the page or pages that may be jammed.
It means that the high limit or flame rollout switch is open. This can lead to error code 13, Limit Circuit Lockout. Error 13 means that the limit or flame rollout has been open for more than 3 minutes. To address this issue, we need to ensure the furnace has proper air flow, and increase it if necessary.
Displaying of the error code “err 13”. The heat pump does not start. Origin of the problem : This problem corresponds to an excessive air temperature (greater than 43°C).
Clean or replace sensor. Test sensor resistance. Replace burner assembly. Call Rheem tech support for possible do-it-yourself help.
Unfortunately, a credit card decline (Authorization error: Generic Decline) means that your card issuer or bank has declined the transaction we`re trying to charge to your card.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Error Code 51.1 says Printer Error No Kidding.lol
ANSWER : Sometimes turning off and on will allow you to print a few pages. The error is a beam detect error. The only real fix is to replace the laser scanner unit. Could be a loose connector on the scanner or DC controller from the scanner. That’s unlikely. You could try the only other free fix which is to open the scanner assy. and clean all the mirrors inside. The dust could obstruct the laser beam enough to cause the detect error.

Read Full Q/A … :
Unknown Printer

Error Code 52.1M
ANSWER : Magenta laser error. The spinning motor bearings cause the squeal and that slows it down causing the error. You could try opening it and lubricating the motor shift with a drop of synthetic lubricant. Do not use more than a drop.

Read Full Q/A … :
Unknown Printer

Scanner error keeps coming up
ANSWER : I am having the same problem with my Epson Workforce 645

Read Full Q/A … :
Unknown Printer

HP CLJ CP 5225 ERROR 55.0601
ANSWER : my printer cp5225 is giving me error code 55.0601 message which i can’t fix please help

Read Full Q/A … :
Unknown Printer

Error Message 4F on MFC 210C
ANSWER : Basically this kind of error caused by loss of voltage on print head. If this is the case then I suggest to buy a new printer rather than replace print head. Print head might be too costly.

Read Full Q/A … :
Unknown Printer

HP 9040 MFP Error code
ANSWER : bonsoir

Read Full Q/A … :
Unknown Printer

Density Shutter Error
ANSWER : I’ve never worked on one of those printers, but I have never, ever seen 1 valid solution for printer repair on fixya.com I read the replies there when I need a good laugh. Makes me wonder what the “techs” on that forum actually do for a living. It certainly couldn’t be printer repair.

Read Full Q/A … :
Unknown Printer

52.0 SCANNER ERROR
ANSWER : Laser scanner assembly.

Read Full Q/A … :
Unknown Printer