Okidata Oki C 5100

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

The common reasons for this issue are various, for instance, the paper input tray is overloaded, dust or moisture can affect the paper feed or paper pick rollers, the printer driver is old, etc. Thus, the printer cannot detect the paper that has been inserted into the tray.
The message “No Paper” will appear on the LCD display if the Brother machine does not detect paper in the paper tray(Tray#1 or Tray#2) or MP(Multi-purpose) Tray. Resetting the Brother machine may resolve this issue.
Check that the same IP address is set for the machine and the machine`s port setting on the computer. Check that the IP address is not duplicated by another device. Check that the correct IP address, subnet mask, and gateway address are set. If using OKI LPR Utility, check the IP address setting with OKI LPR Utility.
A “Load Paper” intervention message appears on the printer display even when there is paper loaded in the tray. This error message means the printer is not detecting any paper on the tray. The same intervention message will appear when: The tray is empty.
Slide the paper all the way into the printer. The leading edge of the paper will stop at the Paper Drive Roller. Locate the Paper Sensor/OOPs sensor on the right side of the paper path. It can be seen from the top of the printer with the Top Cover open and has red, black, and blue wires attached to it.
1 Press and release the SEL key to take the printer off-line. The SEL light will be out. 2 Then, press and hold the SHIFT key and press the RESET (CHARACTER PITCH) key. 3 The printer is reset.
Capacitive sensors can detect objects that have a dielectric constant that is different from air. Hence, these sensors can detect objects made from a wide variety of materials such as plastic, paper, wood, etc.
The automatic paper type sensor functions when a tray is configured to the. Any Type. or plain type. setting. After it has picked up paper from the tray, the product can detect overhead transparencies, paper.
Do a hard reset on your printer. To do this you just need to turn off your printer, unplug for a few minutes and then plug the printer again. If that still doesn`t work, try turning the printer and your computer off, and then start it back up again. Try uninstalling and then reinstalling your printer driver.
When the printer is in sleep mode, press the [Power Save/Wake Up] button on the operator panel and confirm that “Ready To Print” displays. If “Ready To Print” is displayed, the following restrictions do not apply.
Still not working? Your thermal printer probably needs a good cleaning. We recommend using Thermal Printer Cleaning Cards with every paper roll change to remove residue and other contaminants from thermal print heads, paper guides and paper paths, helping to prevent paper jams and misprints.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.
ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.

Read Full Q/A … :

Okidata Oki C 5100

Paper won't advance on Okidata 320 Turbo
ANSWER : Check the top and rear paper sensors to make sure they are not obstructed, stuck, or bad.

Read Full Q/A … :

Okidata Oki C 5100

RESET OKIDATA TONER DRUM
ANSWER : Hi guys

Read Full Q/A … :

Okidata Oki C 5100

CANON P200- ERROR 5100 PLEASE HELP!
ANSWER : Read this for solutions http://www.mytechtime.com/2011/10/canon-error-5100-how-to-fix.html

Read Full Q/A … :

Okidata Oki C 5100

RESET OKIDATA TONER DRUM
ANSWER : HI there, oki image drums contain a fuse. You can reset them if they are working/printing ok by replacing the fuse. Hope this helps. The fuse is located inside the unit so is a bit fiddly.

Read Full Q/A … :

Okidata Oki C 5100

paper drive wont accept paper
ANSWER : There is probably a small scrap of paper stuck at the left edge of the paper path. The paper hits it and skews to the left. The smaller size bypasses it. You need to shove something stiff, like a piece of file folder, down the paper path and attempt to dislodge it.

Read Full Q/A … :

Okidata Oki C 5100

Canon Pixma MP150 Error Code 5100
ANSWER : Make sure you check that a copy of Gustave Holst’s journey to the stars cassette isn’t stuck in there! haha. That’s what my error 5100 was all about, I was getting ready to dismantle the thing after threatening it with a water boarding.

Read Full Q/A … :

Okidata Oki C 5100

Error message to load paper and push OK, but not out of paper
ANSWER : I assist the binary options for a long time, and only half this past year I decided to alter the strategy for a better, she called for help Bing and he gave me this web site http://bestoptionstrategies.net .Now I focus on the suitable technique for themselves, and things gone up. I think everybody else faced with this particular problem. I believe my estimation will soon be helpful to you.

Read Full Q/A … :

Okidata Oki C 5100