Unknown Printer

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Check that the same IP address is set for the machine and the machine`s port setting on the computer. Check that the IP address is not duplicated by another device. Check that the correct IP address, subnet mask, and gateway address are set. If using OKI LPR Utility, check the IP address setting with OKI LPR Utility.
Error: 400. Paper size error has occurred in the indicated tray. Make sure that the size of paper loaded in the tray matches the [Paper Size] setting set on the operator panel. Load paper according to the paper size and direction set.
If your printer`s status displays “Printer in error state,” there may be a problem with the printer itself. Make sure the printer is turned on and connected to your PC by Wi-Fi or cable. Check it for low paper or ink, and be sure the cover isn`t open and the paper isn`t jammed.
Check that the correct paper is properly loaded into the printer and is not jammed. Replacing damaged cables, plugging in loose or disconnected cables, and fixing paper jams as necessary may resolve the issue.
Open the printer`s web page and Sign in as Administrator. On the General tab select Reset Factory Settings in the menu.
Error: 490, 491, 492, 493, 494. No paper is loaded in the indicated tray. Load paper of the displayed size.
1. Paper Jams. Paper jams are a common problem for printers, resulting in time-consuming and frustrating delays. It can occur when loose sheets of paper get stuck in the rollers or feeding mechanism of the printer.
Turn the printer on while holding down the FORM FEED button. This test prints the character set in a rolling pattern using the default type style. Press the SELECT button or turn off the printer to stop the test. Oki Data has taken care to insure that the information is complete, accurate and up-to-date.
Most printers will stop working when they`re out of paper, ink or toner, or if the unit detects an issue with the ink or toner cartridge. When this occurs, you might receive an error message or notice blinking green or amber lights on your printer.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Oki error codes
ANSWER : Hi,

Read Full Q/A … :
Unknown Printer

Density Shutter Error
ANSWER : I’ve never worked on one of those printers, but I have never, ever seen 1 valid solution for printer repair on fixya.com I read the replies there when I need a good laugh. Makes me wonder what the “techs” on that forum actually do for a living. It certainly couldn’t be printer repair.

Read Full Q/A … :
Unknown Printer

Error Code 51.1 says Printer Error No Kidding.lol
ANSWER : Sometimes turning off and on will allow you to print a few pages. The error is a beam detect error. The only real fix is to replace the laser scanner unit. Could be a loose connector on the scanner or DC controller from the scanner. That’s unlikely. You could try the only other free fix which is to open the scanner assy. and clean all the mirrors inside. The dust could obstruct the laser beam enough to cause the detect error.

Read Full Q/A … :
Unknown Printer

Error code 79 on Oki Page 12i/n
ANSWER : Open the lid of the printer and check the two cables on the right side (on the inside of the lid). Make sure both cables are introduced correctly in the plugs. This should resolve the problem. Good luck, Mark

Read Full Q/A … :
Unknown Printer

Which NIC and NIC F/W download and where find it OKI C511dn
ANSWER : Sorry, the right address: https://mega.nz/#F!oEkA3JKZ!YiWuhQTBl5ym-ilNRPYTaw

Read Full Q/A … :
Unknown Printer

Firmware(EEPROM) Oki C9650n.
ANSWER : Try the stuff I’ve find searching my OKI C511dn net card (still searching)

Read Full Q/A … :
Unknown Printer

Oki C5300 problem : network menu disappeared.
ANSWER : You need MuWin and your NIC firmware to upload to the host, but both things are keep under cover by OKI… Find attached old (and probably useless for you) files; check and say.. (https://mega.nz/#F!oEkA3JKZ)By the way, you should specify what firmware do you need ┬┐isn’t it? I don’t know yet what firmware uses my c511dn nor what NIC host it mounts… :~(

Read Full Q/A … :
Unknown Printer

Error Message 4F on MFC 210C
ANSWER : Basically this kind of error caused by loss of voltage on print head. If this is the case then I suggest to buy a new printer rather than replace print head. Print head might be too costly.

Read Full Q/A … :
Unknown Printer