Unknown Printer

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Sometimes a paper jam error persists even though there is no jammed paper (false paper jam). Reset the printer, which might clear a false paper jam error, and then try to print again. With the printer turned on, disconnect the power cord from the printer. Unplug the power cord from the power source.
If the paper is even slightly askew, the rollers will pick it up a little crooked, and — guess what — the crooked sheet will immediately get jammed. So even though there`s no paper stuck when you start printing, the loose paper guides are ensuring that a sheet gets jammed whenever the printer starts doing its thing.
The paper tray is not completely inserted into the product. The paper settings in the print driver do not match the paper loaded in the paper tray. The rubber paper-feed rollers are dusty.
The way I solved it was to restart the print spooler. This will reset Window`s communication with the printer and Windows will no longer think the printer is out of paper. Problem solved.
Do a hard reset on your printer. To do this you just need to turn off your printer, unplug for a few minutes and then plug the printer again. If that still doesn`t work, try turning the printer and your computer off, and then start it back up again. Try uninstalling and then reinstalling your printer driver.
Slide the paper all the way into the printer. The leading edge of the paper will stop at the Paper Drive Roller. Locate the Paper Sensor/OOPs sensor on the right side of the paper path. It can be seen from the top of the printer with the Top Cover open and has red, black, and blue wires attached to it.
A piece of paper stuck in the paper tray or inside the printer can create a paper jam. Paper jams can occur for a variety of reasons, such as overloading the paper tray, loading different thicknesses of paper in the tray, or using paper that isn`t appropriate for your particular printer.
The paper might not be engaged with the feed rollers. The paper-width guide is pressed against the paper stack too tightly. The paper tray is not completely inserted into the product. The paper settings in the print driver do not match the paper loaded in the paper tray.
If your printer`s status displays “Printer in error state,” there may be a problem with the printer itself. Make sure the printer is turned on and connected to your PC by Wi-Fi or cable. Check it for low paper or ink, and be sure the cover isn`t open and the paper isn`t jammed.
The sensor detects plain and photo papers (glossy and matte) and the printer automatically adjusts ink levels for the appropriate amount of ink for the paper.
The use of a capacitive sensor is recommended if the object being detected is made from plastic, mineral, glass, wood, or paper, or is an oily or aqueous liquid, or a granulate or a powder, and the required detection distance is within a range of a few millimeters.
One of the most common causes of paper jams is that the paper has simply not been loaded correctly into the printer paper feed. With this in mind, remove any paper from the tray in order to check for any jams. If you do see some paper jammed, pull each sheet out of the printer slowly until the printer is clear again.
Step one: Perform a power reset

Unplug the power cord from the wall outlet. Wait at least 15 seconds. Plug the power cord back into the wall outlet. Reconnect the power cord to the rear of the product.

Shut the printer off, get a flashlight, and try to see inside. Make sure no label fragments have jammed up your printer before proceeding. You might need to check underneath the printer and shake it out to dislodge any loose paper or other debris that may have gotten stuck inside.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.
ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.

Read Full Q/A … :
Unknown Printer

Brother MFC-J6510DW extra paper tray.
ANSWER : There clearly was a similar problem couldn’t enter in to a ditch of benefit drawing up a strategy. A pal gave this http://put-call-options.com site to select an appropriate technique and I have chosen for themselves the optimum and successful naybolee. I hope I served you with your problem. Thanks for attention)))

Read Full Q/A … :
Unknown Printer

BROTHER MFC 490CW/ MFC 210C
ANSWER : The industry says that at least once a month you should print something, even a test print page to avoid the ink drying up in the print heads. Most printers including Brother will turn themselves on occasionally to clean themselves. I do not recommend refilling your ink cartridges yourself. You can buy ‘non-OEM compatible refilled’ ink cartridges for you printers very cheaply but not all that make/sell these are of the same quality. So if this is of interest to you then you need to shop around until you find a good & reputable compatible non-OEM ink seller.

Read Full Q/A … :
Unknown Printer

Paper jam in front of print head. HELP URGENT Please
ANSWER : I am 99% sure you don’t have a problem with a sensor. Having no idea what you do in the cleaning process, and not being able to look at the printer, there is no way to help or advise you.

Read Full Q/A … :
Unknown Printer

Error Message 4F on MFC 210C
ANSWER : Basically this kind of error caused by loss of voltage on print head. If this is the case then I suggest to buy a new printer rather than replace print head. Print head might be too costly.

Read Full Q/A … :
Unknown Printer

Error Message "Paper out" when paper loaded
ANSWER : Check your paper tray settings as printer may be looking for paper from the manual feed tray on top of printer.

Read Full Q/A … :
Unknown Printer

Error message to load paper and push OK, but not out of paper
ANSWER : I assist the binary options for a long time, and only half this past year I decided to alter the strategy for a better, she called for help Bing and he gave me this web site http://bestoptionstrategies.net .Now I focus on the suitable technique for themselves, and things gone up. I think everybody else faced with this particular problem. I believe my estimation will soon be helpful to you.

Read Full Q/A … :
Unknown Printer

Brother MFC 8220
ANSWER : This problem is normally caused by the fuser. There’s a brown driver gear who frequently broke and you’ll be obliged to replce it to take care of the problem.

Read Full Q/A … :
Unknown Printer