Unknown Printer

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Make sure your paper meets the specifications for your product. If paper dust builds up on the rollers, they may lose traction and become unable to feed paper properly. Clean the paper guide. If roll paper does not feed, cut the end straight across and uncurl it by rolling it backward, if necessary.
Make sure the paper size selected in the printer software matches the paper size selected on the printer`s control panel. To verify the paper size on the printer`s control panel press, Home if necessary, then select Setup > Paper Setup. If this does not resolve the issue, contact Epson.
All Epson printer models contain a factory reset button on the back of the printer body that can be used to return the printer to factory settings. Using the Power button, turn off the printer. Press and hold the Reset button with a cell. Turn on the printer, but hold down the Reset button for a few seconds.
Select > Paper Setting > paper source > Print Adjustments > Paper Feed Adjust. Select one of the following: Auto: automatically adjusts the paper feed setting (takes 9 to 35 minutes to complete); Epson recommends running this option first.
The maximum paper width is 10.1 inches (257 mm). The maximum printable width is 8 inches (203.2 mm). For single sheets wider than 8.23 inches (209.2 mm), the side margins increase proportionally to match the width of the paper.
Dot Matrix Printer Epson Lx-310, Paper Size: A4, Model Name/number: Epsol Lx 310.
Click Start, point to Settings, and the click Printers. Right-click the appropriate printer, and then click Properties. Click the Paper tab, and then click the paper size you want to use in the Paper Size box. Click OK, and then close the Printers folder.
To run the test, turn on the printer while holding down the LF/FF button or Load/Eject button. Self test is printed in Draft characters when the LF/FF button is held, or in NLQ characters when the Load/Eject button is held. When using single-sheet paper, load paper in the printer.
Yes, you can reset the print settings to their original, default values. Press and hold down the Cancel button for 3 seconds. When the message to reset the printer to default settings appears, press OK to reset the print settings.
If the paper feed rollers are dirty or paper powder is attached to it, paper may not be fed properly. In this case, clean the paper feed rollers. Cleaning will wear out the paper feed rollers, so perform this only when necessary. Make sure that the power is turned on and remove any paper from the rear tray.
Push down the release lever to slightly raise the feeder mechanism and release the paper. Then slowly pull the jammed paper out of the feeder mechanism. (Be careful not to pull too hard; the paper may tear, making it more difficult to remove.) If paper is still jammed inside the mechanism, open the cover to remove it.
Document specifications. The Automatic Document Feeder (B81321 ) allows you to automatically load multi-page documents into your scanner. This is useful for OCR (optical character recognition) scanning, or for creating an image database or PDF files.
If ink smears when you print on thick paper, you can select the Thick Paper setting to improve print quality. Printing is slower with this setting. Press the home button, if necessary.
Paper Sizes: 3.5″ x 5″, 4″ x 6″, 5″ x 7″, 8″ x 10″, 8.5″ x 11″, 8.5″ x 14″, A4, A6, half letter, executive, user definable (3.5″ x 5″ – 8.5″ x 47″)Maximum Paper Size: 8.5″ x 47.2″Paper Types: Plain paper. Epson Bright White Paper.
Push down the release lever to slightly raise the feeder mechanism and release the paper. Then slowly pull the jammed paper out of the feeder mechanism. (Be careful not to pull too hard; the paper may tear, making it more difficult to remove.) If paper is still jammed inside the mechanism, open the cover to remove it.
A paper feed issue can occur for several reasons, such as dusty or contaminated paper rollers, the condition of the paper in the tray, or even issues with the software.
A paper feed issue can occur for several reasons, such as dusty or contaminated paper rollers, the condition of the paper in the tray, or even issues with the software.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.
ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.

Read Full Q/A … :
Unknown Printer

Canon Pixma Printer Paper Does Not Feed Properly/"No Paper" Error Occurs?
ANSWER : Pretty much useless advice. I also have serious doubts about someone who is obviously not fluent in the English language.

Read Full Q/A … :
Unknown Printer

Paper feeds straight through without printing on an Epson R2400
ANSWER : I was able to get it to print the internal test page by holding down the sheet paper feed button while turning the machine on — then continuing to hold the sheet paper feed button. It took several attempts, feeding a page straight through, but eventually it caught the sheet and printed. So it may be a timing issue as others have mentioned. It could still mean that the feed rollers are worn out. The back side of the large D-shaped feed roller has visible abrasion on it. The abrasion is difficult to see as the roller does not stay with the flat side exposed.

Read Full Q/A … :
Unknown Printer

Canon MP110 won't print, paper won't feed
ANSWER : Thanks everyone!!!! My printer was working fine yesterday and then at night it would not print. Got very frustrated. It would say load paper but there was paper. Then it would only take one side of the paper and say paper jam and there was no jam. Today I landed on this page after searching online and I shook my printer.. Yes!!!!! and now it prints… You cannot imagine how happy I am… Doing the happy dance now!!!! Thanks everyone 🙂

Read Full Q/A … :
Unknown Printer

when printing front and back, the front will print well but the back will fade
ANSWER : It happens because second side voltage is much higher and the board breaks. Are you getting this issue in auto duplex only, or same error you are getting when you print second side manually?

Read Full Q/A … :
Unknown Printer

Paper feed
ANSWER : Judging by your other post, you must have read that you need to remove the laser scanner assy and lubricate the spinning mirror shaft. Good luck.

Read Full Q/A … :
Unknown Printer

Error Message "Paper out" when paper loaded
ANSWER : Check your paper tray settings as printer may be looking for paper from the manual feed tray on top of printer.

Read Full Q/A … :
Unknown Printer

Error message to load paper and push OK, but not out of paper
ANSWER : I assist the binary options for a long time, and only half this past year I decided to alter the strategy for a better, she called for help Bing and he gave me this web site http://bestoptionstrategies.net .Now I focus on the suitable technique for themselves, and things gone up. I think everybody else faced with this particular problem. I believe my estimation will soon be helpful to you.

Read Full Q/A … :
Unknown Printer