Unknown Printer
How to Identify and Fix Common Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
Do a hard reset on your printer. To do this you just need to turn off your printer, unplug for a few minutes and then plug the printer again. If that still doesn`t work, try turning the printer and your computer off, and then start it back up again. Try uninstalling and then reinstalling your printer driver.
Check that the correct paper is properly loaded into the printer and is not jammed. Replacing damaged cables, plugging in loose or disconnected cables, and fixing paper jams as necessary may resolve the issue.
HP Smart app might display the “Printer status unknown” error message if your printer is idle or offline. If your printer goes into sleep or standby mode after a period of inactivity, press the power button to “wake” it.
Make sure that both ends of the USB cable are correctly inserted into the computer and the printer. Try disconnecting and reconnecting the USB cable at both ends. Disconnect the printer and the computer and reconnect them. Try another USB port if available.
Select Start , then select Settings > Devices > Printers & scanners . Scroll down to Related Settings and select Print server properties. Select the Drivers tab, and see if your printer is listed. If it is, you`re all set.
Status unknown means a circumstance where samples were scheduled to be taken by the regional water quality control plant and were not, samples were taken but not yet analyzed by the report due date or where a new discharger has yet to be sampled.
If you`re using Windows 10, click or tap the “+ Add a printer or scanner” button. No matter if you`re using Windows 11 or Windows 10, the operating system begins “searching for printers and scanners,” and if it manages to find your local printer or scanner, it will try to install its drivers automatically.
Alternative USB connection options
- Make sure there is an open USB port available directly on your computer. …
- Connect the printer USB cable to the computer. …
- Search for and open Printers & scanners.
- Click Add a printer or scanner.
Follow the steps below to add a network printer in Windows 10.
- Open the Windows Start menu. …
- Then click to Settings. …
- Then click on Devices.
- Next, select Printers & Scanners. …
- Then click Add a Printer. …
- Click “The printer that I want isn`t listed.” Once you select this, the “Add Printer” screen will pop up.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Print file sent but no printing occurs
ANSWER : Been working on these since they first were released. Never seen a problem like yours. If it happens again, try doing an engine test, as it bypasses the formatter board. The engine test is located at the right side of the manual tray opening. Look for a hole in the side wall. Stick something like a paper clip into it to actuate the test button. It will then print a lined test page. If it does that, then it points to the formatter board as the cause of your problem.
Read Full Q/A … :
Unknown Printer
Unknown Printer
Prints blank pages, won't print from computer
ANSWER : Don’t know why you replaced the fuser, but assuming you had print before, then it must have been something you did during the procedure. Only thing I can suggest is to recheck your work. Just because you reinstalled a connector doesn’t mean that it is seated firmly enough to work. Any flat ribbon connectors that you removed and reinstalled, check to see that the contacts are all flat and not peeled back.
Read Full Q/A … :
Unknown Printer
Unknown Printer
My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.
ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.
Read Full Q/A … :
Unknown Printer
Unknown Printer
when printing front and back, the front will print well but the back will fade
ANSWER : It happens because second side voltage is much higher and the board breaks. Are you getting this issue in auto duplex only, or same error you are getting when you print second side manually?
Read Full Q/A … :
Unknown Printer
Unknown Printer
LJ 4200 Downld file now (Download file now)
ANSWER : just thanks this password generator that can allow you hack snapchat account online without any error at all.
Read Full Q/A … :
Unknown Printer
Unknown Printer
HP Deskjet 640c wont print??
ANSWER : yes
Read Full Q/A … :
Unknown Printer
Unknown Printer
Epson Artisan 835 print head cleaning question
ANSWER : I had the same problem. After reading the comments, I tried Liquid Wrench spray. 1st try got about sixty percent improvement. Tried again this time I let it set for about 10 min then did a head cleaning. Completely solved the problem. I am a little concerned about its use on plastic. So far so good.
Read Full Q/A … :
Unknown Printer
Unknown Printer
My printing come out blurred
ANSWER : doris…There are usually 2 reasons for blurry output on this printer. First, make sure that the alignment is correct. You can get to it from the maintenance tab on the software that came with the printer. The other common cause of blurring is debris under the printhead. Hope this helps.
Read Full Q/A … :
Unknown Printer
Unknown Printer