HP LaserJet 6MP
How to Identify and Fix Common Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced technical support :
An Er/04, Er/05, or Er/06 error message indicates a paper jam. Find and clear the printer of any jammed paper, or reset the printer if the printer has no jammed paper.
If you are experiencing an “50.2F. 00 Fuser error”, first turn the printer off and back on. Sometimes the error will temporarily go away with a reboot so you can print a few more pages, but usually the error reappears.
The message `Fuser Error` or `Self-Diagnostic` means either the fuser has reached the maximum temperature allowed or there has been an error in detection of the correct temperature during specific times of the printing process.
The Error Code 6 means that there was an issue communicating with the Google Play app on the phone (various possible reasons). 1) Reboot the device and try the purchase again.
An E5 or E6 error occurs when the scanner or printer is in an error state. Reset the printer. With the printer on, disconnect the power cord from the printer. Unplug the power cord from the power source.
An Er/04, Er/05, or Er/06 error message indicates a paper jam. Find and clear the printer of any jammed paper, or reset the printer if the printer has no jammed paper.
The fuser unit or fuser is a critical part of any laser printer. Using pressure and heat, it fuses the toner powder onto the page to create a print, and without it, the printer cannot operate.
The 1686 support code signifies that the printer has detected an issue with one or more of your ink cartridges.
Troubleshoot a blinking orange light on HP DeskJet.
It indicates firmware issues, paper jams, or improperly installed cartridges. Resolve it by performing a power reset of your printer. Take out the installed cartridges. Disconnect the device by removing the power cord from the outlet and the rear end.
Communication Fault (E6) Check the communication wire between indoor unit and outdoor unit to ensure if the wire is open circuited or short circuited and if the connector is loose.
Take some time to clean your filter and check your chemicals on a daily basis. At this point the error code should be cleared – if the Error message persists, this could suggest that your liner has constricted tubes.
a misprint or misspelling in a text.
Take some time to clean your filter and check your chemicals on a daily basis. At this point the error code should be cleared – if the Error message persists, this could suggest that your liner has constricted tubes.
Turn off the HP printer and unplug it from the power source. Also, shut down your computer and unplug any external devices. Wait for a few minutes and then plug in the printer and turn it back on. Finally, turn on your computer and check if the error state has been resolved.
Turn off the HP printer and unplug it from the power source. Also, shut down your computer and unplug any external devices. Wait for a few minutes and then plug in the printer and turn it back on. Finally, turn on your computer and check if the error state has been resolved.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
ERROR on HP LJ 4525
ANSWER : Print a Configuration page. That will tell you what size paper Tray 2 thinks it has in it. If it doesn’t have plain letter on the page, then it will ask to print from Tray 1.
Read Full Q/A … :
HP LaserJet 6MP
Printer jams paper from both trays even after replacing pick up roller
ANSWER : Update: I have the duplex model, and when the paper seems to reach the point where it jams, the printer squeals like two rubber parts are rubbing together when they’re not supposed to.
Read Full Q/A … :
HP LaserJet 6MP
Error Code 51.1 says Printer Error No Kidding.lol
ANSWER : Sometimes turning off and on will allow you to print a few pages. The error is a beam detect error. The only real fix is to replace the laser scanner unit. Could be a loose connector on the scanner or DC controller from the scanner. That’s unlikely. You could try the only other free fix which is to open the scanner assy. and clean all the mirrors inside. The dust could obstruct the laser beam enough to cause the detect error.
Read Full Q/A … :
HP LaserJet 6MP
replace with new imaging unit error
ANSWER : samsung clp 365w firmware
Read Full Q/A … :
HP LaserJet 6MP
Samsung ML 2165 Error lights
ANSWER : Hi there, I am having the same problem. Stupidly I bought a second replacement (genuine Samsung) cartridge thinking it may have been a faulty cartridge as sometimes it deemed to work after a bit of messing around. SO NOW I HAVE ONE NEARLY NEW AND ONE COMPLETELY NEW ; ABSOLUTELY NO USE TO ME – unless I can get the printer to accept them.
Read Full Q/A … :
HP LaserJet 6MP
Printer will not pick-up paper from either tray. All error lights are on.
ANSWER : That is a hard fault. You need to access the secondary fault codes to diagnose what is causing it. Follow the instructions at this link http://www.printcopy.info/?l=en&mod=free&chap=erc&brand=HP&model=LaserJet%205P&page=4
Read Full Q/A … :
HP LaserJet 6MP
LJ 4250N Tray 2 Clearing Paper Path 41.3 Error
ANSWER : i saw sAme problem in my client printer hp lj 4250 . its toner problem . when i am the toner change then printer is 100% ok.
Read Full Q/A … :
HP LaserJet 6MP
Error light is on
ANSWER : Assuming it is the triangle shaped error light, it can mean the tray is empty, a door is open or there is a paper jam. Did you check thoroughly for a jam? I’ve opened them up and there was a paper stuck below the cartridge in plain sight. Happened more than a few times. That’s why I ask. Also remove the tray and look up into where the slot for the paper to feed into the printer is. Often, there is a paper stuck in there. Lastly, open the back and look carefully for any scraps of paper. People often neglect to mention there was a paper jam and they ripped it out and it didn’t come out in one piece. I guess that’s not important enough to convey to someone trying to fix it.
Read Full Q/A … :
HP LaserJet 6MP