Unknown Printer

Experienced technical support provide their insights in answering this question :
i saw sAme problem in my client printer hp lj 4250 . its toner problem . when i am the toner change then printer is 100% ok.

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

If you are seeing the 41.3 error on a LaserJet 4, 4Plus, or 5 series printer, and you find a blank sheet of paper in the path, your printer is probably having a failure with the solenoid on the paper feed assembly. This is becoming a common issue as these printers get older.
41.2 Error Code on HP Laser Printers

The 41.2 is still is a laser/scanner error—the good old “temporary loss of beam detect.” And in most printers, the possible causes are the same as always: bad laser/scanner (by far the most common), bad DC controller board, or bad connections between these two.

The 41.2 error in the LaserJet 5Si, 8000, 8100 and 8150 is typically caused by high voltage arcing that disrupts the beam detect circuit. The most common cause of arcing is a bad connection to the transfer roller.
The jam message may vary depending on the location of the page or pages that may be jammed. At times, a related message such as a “13.01 Paper Jammed in Tray 2” which indicates that the paper did not arrive at the pre-feed sensor (PS102) in the amount of time allotted by the DC Controller.
This is tipically caused if two or more sheets stick together in the product or if the tray is not properly adjusted“.
In some cases the reason for error code 41.7 is that the rollers grabbing fresh paper are not sticky enough any more. In this case I used spray for climbing skins (e.g. colltex) to make them stickier again, and the problem was resolved.
Verify that the toner cartridge and the transfer roller are seated correctly. Ensure that the tray pickup, feed, and separation rollers are installed correctly and show no damage or wear. Check if the rollers are installed correctly.
Check printer configuration

Incorrect configuration of printer related settings can also cause “Printer not activated, error code 41”. This problem is also known to come up if the selected printer is not set as the default printer to carry out the printing tasks.

If your printer`s status displays “Printer in error state,” there may be a problem with the printer itself. Make sure the printer is turned on and connected to your PC by Wi-Fi or cable. Check it for low paper or ink, and be sure the cover isn`t open and the paper isn`t jammed.
Recommended action. Turn the printer off, wait 15 seconds and turn the printer back on (using the power switch located on the back of the printer). The error code should not appear again.
41.03 is often caused by paper being set to one size and another sent.
Recommended action. Turn the printer off, wait 15 seconds and turn the printer back on (using the power switch located on the back of the printer). The error code should not appear again.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

LJ 4250N Tray 2 Clearing Paper Path 41.3 Error
ANSWER : i saw sAme problem in my client printer hp lj 4250 . its toner problem . when i am the toner change then printer is 100% ok.

Read Full Q/A … :
Unknown Printer

Paper jam in tray 2 (but no paper pulled from tray) also M476DN models
ANSWER : Isopropyl alcohol is not recommended for rubber rollers. It dries out the rubber and hasten it’s cracking and breaking. It will do nothing to restore the grip. Those rollers are really hard to replace. It would be easy if that dumbass secondary menu really worked. None of the techs I’ve spoke to ever got into it. Everyone I know sends a print job and listens for the roller to rotate into position where you can pull it off.

Read Full Q/A … :
Unknown Printer

My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.
ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.

Read Full Q/A … :
Unknown Printer

HP 4250n error 13.05.00 Phantom Jam
ANSWER : Pull and reset the fuser. Make sure both sides are back into their position.

Read Full Q/A … :
Unknown Printer

Error Message "Paper out" when paper loaded
ANSWER : Check your paper tray settings as printer may be looking for paper from the manual feed tray on top of printer.

Read Full Q/A … :
Unknown Printer

Canon Pixma Printer Paper Does Not Feed Properly/"No Paper" Error Occurs?
ANSWER : Pretty much useless advice. I also have serious doubts about someone who is obviously not fluent in the English language.

Read Full Q/A … :
Unknown Printer

HP 4250n 41.3 unexpected paper size
ANSWER : BULLSHIT

Read Full Q/A … :
Unknown Printer

Error message to load paper and push OK, but not out of paper
ANSWER : I assist the binary options for a long time, and only half this past year I decided to alter the strategy for a better, she called for help Bing and he gave me this web site http://bestoptionstrategies.net .Now I focus on the suitable technique for themselves, and things gone up. I think everybody else faced with this particular problem. I believe my estimation will soon be helpful to you.

Read Full Q/A … :
Unknown Printer