Unknown Printer

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Check Cables and Printer USB Ports

Check all cable connections (including the power cord) on the printer side. If the printer does have power and you`ve properly connected the communication cable, but the printer is still not recognized, try switching to a different USB port on the PC.

Or try this. 1) Take out the cartridges. 2) Unplug the power cord from the printer & wall. 3) Wait for 30 seconds.
Select Start, type Control Panel, and then press Enter. In Control Panel, select the View Devices and Printers item. Select Add Printer at the top of the window. After the wizard started, select The printer that I want isn`t listed.
Your printer should have been packaged with a USB cable regardless of whether it is a wireless or wired printer. Plug the cable into your printer and your computer`s USB port. The direct linking should trigger your computer to recognize the printer and start up the software needed to complete the installation.
Click Start on your computer, then select Devices and Printers. Right-click on the printer`s icon that did not install correctly, then select Troubleshoot. After you confirm that the printer driver for the device you want to use is not installed, select Apply this fix.
Open the start menu and select Control Panel > Administrative Tools > and choose the Services icon. Locate the Print Spooler service and right-click. Then select the option to “Stop” the service.
If your printer`s status displays “Printer in error state,” there may be a problem with the printer itself. Make sure the printer is turned on and connected to your PC by Wi-Fi or cable. Check it for low paper or ink, and be sure the cover isn`t open and the paper isn`t jammed.
In the Active Printers dialog box, select the printer you want. In the printer dialog box, select the print job you want to cancel. Note: If you`re using Windows 10, you might need to select the printer you`re using first. Click Document > Cancel.
Make sure that both ends of the USB cable are correctly inserted into the computer and the printer. Try disconnecting and reconnecting the USB cable at both ends. Disconnect the printer and the computer and reconnect them. Try another USB port if available.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Print file sent but no printing occurs
ANSWER : Been working on these since they first were released. Never seen a problem like yours. If it happens again, try doing an engine test, as it bypasses the formatter board. The engine test is located at the right side of the manual tray opening. Look for a hole in the side wall. Stick something like a paper clip into it to actuate the test button. It will then print a lined test page. If it does that, then it points to the formatter board as the cause of your problem.

Read Full Q/A … :
Unknown Printer

My printer feeds through one piece of paper all the way and then a half piece of paper and stops. I pull out the paper to stop the paper jam and then it prints but sounds rough. After printing, it doesn't feed the paper all the way through.
ANSWER : And the first 2 sheets, the full and half sheet that go through first, are blank.

Read Full Q/A … :
Unknown Printer

when printing front and back, the front will print well but the back will fade
ANSWER : It happens because second side voltage is much higher and the board breaks. Are you getting this issue in auto duplex only, or same error you are getting when you print second side manually?

Read Full Q/A … :
Unknown Printer

HP LJ 1150 Printing multiple pages on one sheet?
ANSWER : Hey friends.

Read Full Q/A … :
Unknown Printer

Epson Artisan 835 print head cleaning question
ANSWER : I had the same problem. After reading the comments, I tried Liquid Wrench spray. 1st try got about sixty percent improvement. Tried again this time I let it set for about 10 min then did a head cleaning. Completely solved the problem. I am a little concerned about its use on plastic. So far so good.

Read Full Q/A … :
Unknown Printer

Prints blank pages, won't print from computer
ANSWER : Don’t know why you replaced the fuser, but assuming you had print before, then it must have been something you did during the procedure. Only thing I can suggest is to recheck your work. Just because you reinstalled a connector doesn’t mean that it is seated firmly enough to work. Any flat ribbon connectors that you removed and reinstalled, check to see that the contacts are all flat and not peeled back.

Read Full Q/A … :
Unknown Printer

LaserJet 4 won't Power Up
ANSWER : I haven’t seen that particular behavior on that model. It either works or it doesn’t. My first choice would be the power supply.

Read Full Q/A … :
Unknown Printer

HP 4101MFP Hard Drive Question
ANSWER : To initialize: turn off – Press start and hold down while turning on, release after all three light light, you should see initialize disk hit check, and allow to boot.

Read Full Q/A … :
Unknown Printer