Epson Stylus Photo R200

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

When the red H ink light flashes, one or more ink cartridges are low on ink. When the red H ink light stays on, you need to replace the cartridge(s). When you print, you`ll also see a message on your screen telling you which cartridge is low or empty.
The ink levels may be low and you may need to refill the ink. Visually check the ink levels. Also make sure you filled the tanks with the correct colors of ink. After you print, the colors in your printout need time to set as the ink dries.
The Cause of Clogs

Printheads clog because nozzles get blocked by either air or ink. Clogs usually happen when: You keep printing with depleted ink cartridges. Using empty ink cartridges can result in air bubbles that can clog your cartridge and/or printhead.

The product is busy. Wait for the power light to stop flashing before turning off the product. If you just replaced an ink cartridge and the power light is still flashing after 3 minutes, the cartridge may be installed incorrectly. Reinstall the ink cartridge.
Most of the time, the flashing red light indicates that you are running low on paper. If the paper is not running low, make sure that the roll is pushed all the way to the back of the printer.
In short, the color management workflow is interrupted and forces a double color management situation. The result is usually prints with a strong magenta cast. The problem usually resolves after a subsequent minor update.
Streaks and unwanted lines could mean that the printer heads are out of alignment. There`s an alignment tool in the printer`s control panel. If that`s not the issue then the printer is dirty. Printer ink stripes may appear along the edges of the paper, which means there`s ink on the rollers and other parts.
A blue or green light indicates the printer is operating correctly, while a red light indicates an error has occurred.
Projector Lamp is Burnt Out

If the light is flashing red or orange, you need to replace the lamp. If the projector turns on, but the image doesn`t appear, your lamp may be burnt out.

A `Paper has Jammed` message and light blinks

Remove any ejected paper from the front or back of the printer. Open the paper tray cover. Remove any loose photo paper from the paper tray, and then check for and remove any bent, wrinkled, or torn paper.

Answer: Red light blinking in L220 printer means the printer may have roller jam problem OR sensor problem occurs. So, please check for roller jam and fix it. Second, check the sensor`s head and clean it too. If you can`t do it manually, then check out the following video tutorial.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

LIGHT LINES ON PRINTED COPIES
ANSWER : You give us so little info to go on. Vertical lines, horizontal lines? On copies, on prints, on both?

Read Full Q/A … :

Epson Stylus Photo R200

Left side light printing
ANSWER : A possibility could be the Charge Transfer Roller mount on the left side broke and it’s not lifting up to push the paper up to the cartridge drum. Take the cartridge out and push down on each end and see if they respond in the same way.

Read Full Q/A … :

Epson Stylus Photo R200

Black line on printed copy
ANSWER : Have absolutely no idea what kind of machine you have so here’s the generic answer. Big copy glass, little copy glass to the left of it. Take window cleaner, put it on paper towel, clean little glass.

Read Full Q/A … :

Epson Stylus Photo R200

when printing front and back, the front will print well but the back will fade
ANSWER : It happens because second side voltage is much higher and the board breaks. Are you getting this issue in auto duplex only, or same error you are getting when you print second side manually?

Read Full Q/A … :

Epson Stylus Photo R200

blue line on printing
ANSWER : Replace the cyan toner cartridge.

Read Full Q/A … :

Epson Stylus Photo R200

vertical lines in the print
ANSWER : Looks like a bad wiper blade in the toner cartridge. They are rubber and with age. Their function is to clean off residue toner on the drum, similar to a windshield wiper blade cleaning off rain drops.

Read Full Q/A … :

Epson Stylus Photo R200

C1660w black printing light
ANSWER : Have someone fixed this? I have the same problem. Please help.

Read Full Q/A … :

Epson Stylus Photo R200

Black line printing in the middle of the page from top to bottom
ANSWER : Take out the toner cartridge and look at the drum. If you see the line, replace the cartridge. If you don’t, then you need to replace the fuser assembly.

Read Full Q/A … :

Epson Stylus Photo R200