Lexmark Optra M

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Make sure that both your computer and your Lexmark printer are connected to your network. Restart your printer. In some cases, a simple restart can fix the issue. Unplug the printer and check if there is any paper stuck in the machine, and if the toner is installed correctly.
If this is the first time a Service Fuser error has appeared on the printer, power it off. Wait ten seconds, and then power the printer on again. The printer should come up to the Ready state. If it does, try printing again.
Make sure that the printer is on the same network with the computer. Make sure that you are using a known working Ethernet cable. Make sure that the Ethernet cable is connected at the back of the printer to the network router, switch, or other network source to which the computer is also connected.
Leave the printer powered off for at least one minute. Power the printer back on. If powering the printer off and on clears the error, continue using the printer but keep an eye on it to see if any printhead errors return. If the printer continues to display a printhead error message, check the message.
Among the more common technical issues that may bring down a printer are disconnected cables, malfunctioning routers, and low ink levels. Moreover, software problems such as interrupted connections or incorrect settings in your system`s drivers can also cause your printer to show up as offline.
The message `Fuser Error` or `Self-Diagnostic` means either the fuser has reached the maximum temperature allowed or there has been an error in detection of the correct temperature during specific times of the printing process.
If your PC or the LCD screen on your printer is telling you that your ink cartridges are full but no ink is passing through to the paper, then it`s most likely that you are dealing with a clogged printhead. Blurry documents and images that appear faded are also signs that it`s time to remove the excess ink.
A print head scratch occurs when an accumulation of dust or debris gets stuck in your machine. And if this happens, the damage cannot be fixed. In most cases, you would need to purchase a new printhead. That`s why it`s important to keep the dust out, away from your machine.
1: Check Printer Power, Cables, and Paper

Check that the correct paper is properly loaded into the printer and is not jammed. Replacing damaged cables, plugging in loose or disconnected cables, and fixing paper jams as necessary may resolve the issue.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Lexmark paper feed problems
ANSWER : On my X204n Lexmark laser printer, it was doing the same thing you described – basically sounded like it was trying to pick up the paper from the tray and then failing after several seconds. When you’d open the paper tray, the paper looked like it had been partially taken up with some black scuff marks on the paper that lined up with the rollers that take up the paper. I inspected the rollers and although they looked a bit smooth and worn, didn’t seem like they should be a problem. However, this particular model has just a rubber tire almost like a car tire – the rubber can come off the hard plastic wheel on the inner portion. So I popped off the two rubber “tires”, turned them inside out and put them back on. When turned inside out, the rubber looked nice and … rubbery and had a lot more grippy feeling to them. The very first printing attempt after that and the paper sucked up perfectly with no problems. I think the problem is solved! So if you have similar “tires” that take up the paper, try flipping them and see if it works for you too.

Read Full Q/A … :

Lexmark Optra M

Lexmark Printer Problems
ANSWER : lexmark printers can be fixed . just follow the steps . uninstall the printer and drivers and install the printer driver and setup again from lexmark and than make sure you internet password and you are all set to go for more visit http://lexmark.technical-care.com/ and i hope this will help you . thanks

Read Full Q/A … :

Lexmark Optra M

Lexmark T654dn power supply problem
ANSWER : Maybe this Thread may be of use:

Read Full Q/A … :

Lexmark Optra M

info on refilling lexmark 16 cartridges?
ANSWER : Our proven track record includes 20 million cartridges sold since 2004, saving $180 million for our customers who would have otherwise bought new cartridges. Unlike many discount cartridge resellers, Inkplicity is a manufacturer, instead of only a distributor mail order firm. By eliminating the wholesaler and maintaining complete control of our cartridges from product design and development to your doorstep, Inkplicity continuously delivers extraordinary savings and quality to you. For more info -Refilled Cartridges

Read Full Q/A … :

Lexmark Optra M

Restore settings Lexmark x466
ANSWER : Try this:

Read Full Q/A … :

Lexmark Optra M

Lexmark Printer Problems
ANSWER : just put them in a dark room together. they’ll make out eventually.

Read Full Q/A … :

Lexmark Optra M

problems with printing
ANSWER : Check your settings to make sure they are Left to Right print order. If they are then reinstall printer driver. If that doesn’t correct problem uninstall printer, reboot computer, and reinstall printer.

Read Full Q/A … :

Lexmark Optra M

Lexmark X466 empty tray
ANSWER : The “Load Tray 1 with A4 paper” means the printer is looking for A4 size paper in Tray 1 and that is not what it is detecting. You need to make sure that the paper size that is in the tray matches what the printer is expecting so it understands that it should be looking for a specific size of paper. If you are printing on regular Letter size paper – set the printer tray to Letter instead of A4 and message should go away.

Read Full Q/A … :

Lexmark Optra M