Lexmark Optra S

How to Identify and Fix Common Problems ?

Our sources include academic articles, blog posts, and personal essays from experienced technical support :

Check that AC line cord is securely connected to both the wall outlet and the back of the printer. Ensure the power switch is turned on. Ensure that particular wall outlet is good by trying some other electronic equipment functions when plugged into that same wall outlet. Try another wall outlet, if possible.
New power button

In these models, the Start/Stop (green) button on the front panel basically functions as the power switch. See the following front panel illustration. To power down the printer, simply hold the Start/Stop button for five seconds.

If your printer`s status displays “Printer in error state,” there may be a problem with the printer itself. Make sure the printer is turned on and connected to your PC by Wi-Fi or cable. Check it for low paper or ink, and be sure the cover isn`t open and the paper isn`t jammed.
Place the smart chip against the pins on the reset device. A red light will flash to show you that the chip is engaged. When the light turns green, usually six or seven seconds later, the cartridge chip is reset and ready to use.
Faulty power cords and connections are an uncommon but possible cause of a printer not turning on. Before suspecting a cord failure, ensure that there is power to the wall outlet and there are no conditions preventing the printer from turning on. Testing by substitution can confirm if a cord connection is the problem.
Solution. Perform a power cycle (power off, wait 30 seconds and then power it on again) on the printer to return its full functionality.
If this is the first time a Service Fuser error has appeared on the printer, power it off. Wait ten seconds, and then power the printer on again. The printer should come up to the Ready state. If it does, try printing again.
Press the tiny reset button located beside the chip and hold for 10 seconds. Depending on the brand and model of the cartridge, you may not need to hold the button for 10 seconds, but it won`t harm the cartridge so do it anyway just to be safe.
Lexmark inks have an approximate shelf life of two years and six months out of packaging. Panasonic has a couple of inkjet printers that use pigment-based ink. Like other ink cartridges, Panasonic ink has a two-year shelf life and will last approximately six months when in use.
Turning the power ON/OFF while the print monitor screen is displayed may cause the printer driver to go off-line and make printing impossible. In this case, open the [Printers / Printers and Faxes / Devices and Printers] folder on the computer and check if your printer driver is shown as off-line.
The fuse protects your printer from short circuits and power overload. It is placed between the power outlet and the switch on the left side of the printer. If your machine does not start after pressing the power switch, at first you should check if the power cable is connected to a power source.
A component found in electrostatic printers, laser printers, and xerographic printers and photocopiers. The fuser unit is used to permanently bond toner to a substrate by applying heat and pressure. A fuser unit is made up of two rollers; one to apply heat and one to apply pressure.
Note: In Sleep mode, the power button is illuminated by a solid (i.e., non-flashing) amber LED. To bring the printer out of Sleep mode, tap the power button once more. This will revert the printer back to its Ready state.
The printer will turn into the sleep mode when the time you have set passes without receiving data after the last job is printed.
Sometimes power-cycling your printer can resolve the issue. Turn off your printer and unplug it, wait 30 seconds, plug your printer back in, and then turn the printer back on.
This can happen for a variety of reasons, from a sudden power outage, low ink, no paper, a paper jam to interference by third-party firewall software.
A hard reset also resets your printer but it doesn`t restore it to factory default settings. This is a better first option if you`ve already customized your printer settings or set up your wireless connection, that way you won`t have to start back at square one.
Power outages do not only cause downtime and delays. They may also damage your equipment, including your DTF transfer printer.
This is a safety feature Lexmark designed for the printer to prevent fire or damage that might result from an overheating fuser. Should it overheat, the printer will automatically shutdown.
You`ll know fairly quickly if your printhead is causing you problems. If your PC or the LCD screen on your printer is telling you that your ink cartridges are full but no ink is passing through to the paper, then it`s most likely that you are dealing with a clogged printhead.
Your printer displays the “Missing or Failed Printhead” error to signal a malfunctioning printhead. The issue could be due to clogged ink nozzles, dirty ink cartridges, internal paper jams, and more. HP printers may also display this error if the printhead pulls air from ink cartridges.
A fuser unit is a pair of heated rollers within the printer that fuses the toner onto the paper being printed on. Toner particles are pulled to the paper to create the desired text and images as the paper passes the imaging drum.
The printer is either low in toner, the density is set too low, or the Economode may be turned on. Remove the toner cartridge and shake it. This will redistribute the toner and often will temporarily solve the problem. However, this usually indicates it is time to install a new cartridge.
Select Control Panel. Select Devices and Printers. Right click on the printer and select Printer Properties. Click Print a Test Page.

Relevant Questions and Answers :

the most relevant questions and answers related to your specific issue

Lexmark X466 empty tray
ANSWER : The “Load Tray 1 with A4 paper” means the printer is looking for A4 size paper in Tray 1 and that is not what it is detecting. You need to make sure that the paper size that is in the tray matches what the printer is expecting so it understands that it should be looking for a specific size of paper. If you are printing on regular Letter size paper – set the printer tray to Letter instead of A4 and message should go away.

Read Full Q/A … :

Lexmark Optra S

info on refilling lexmark 16 cartridges?
ANSWER : Our proven track record includes 20 million cartridges sold since 2004, saving $180 million for our customers who would have otherwise bought new cartridges. Unlike many discount cartridge resellers, Inkplicity is a manufacturer, instead of only a distributor mail order firm. By eliminating the wholesaler and maintaining complete control of our cartridges from product design and development to your doorstep, Inkplicity continuously delivers extraordinary savings and quality to you. For more info -Refilled Cartridges

Read Full Q/A … :

Lexmark Optra S

error 59.99 turn off then turn on
ANSWER : Read this forum thread http://www.fixyourownprinter.com/posts/51164

Read Full Q/A … :

Lexmark Optra S

printer wont switch on
ANSWER : Time for a new printer.

Read Full Q/A … :

Lexmark Optra S

Restore settings Lexmark x466
ANSWER : Try this:

Read Full Q/A … :

Lexmark Optra S

Lexmark paper feed problems
ANSWER : On my X204n Lexmark laser printer, it was doing the same thing you described – basically sounded like it was trying to pick up the paper from the tray and then failing after several seconds. When you’d open the paper tray, the paper looked like it had been partially taken up with some black scuff marks on the paper that lined up with the rollers that take up the paper. I inspected the rollers and although they looked a bit smooth and worn, didn’t seem like they should be a problem. However, this particular model has just a rubber tire almost like a car tire – the rubber can come off the hard plastic wheel on the inner portion. So I popped off the two rubber “tires”, turned them inside out and put them back on. When turned inside out, the rubber looked nice and … rubbery and had a lot more grippy feeling to them. The very first printing attempt after that and the paper sucked up perfectly with no problems. I think the problem is solved! So if you have similar “tires” that take up the paper, try flipping them and see if it works for you too.

Read Full Q/A … :

Lexmark Optra S

Lexmark Printer Problems
ANSWER : lexmark printers can be fixed . just follow the steps . uninstall the printer and drivers and install the printer driver and setup again from lexmark and than make sure you internet password and you are all set to go for more visit http://lexmark.technical-care.com/ and i hope this will help you . thanks

Read Full Q/A … :

Lexmark Optra S

Lexmark T654dn power supply problem
ANSWER : Maybe this Thread may be of use:

Read Full Q/A … :

Lexmark Optra S